Spectrally pure single photons at telecommunications wavelengths using commercial birefringent optical fiber

Jasleen Lugani, Robert J. A. Francis-Jones, Joelle Boutari, Ian A. WalmsleyOptics Express 2020 · DOI

TL;DR

This paper presents a new, cost-effective method for generating spectrally pure single photons at telecommunications wavelengths using readily available birefringent optical fiber. This approach achieves high purity and brightness, paving the way for more accessible and scalable multi-photon quantum optics experiments.

What Problem Does This Paper Address?

Quantum information processing (QIP) relies heavily on the ability to generate and manipulate single photons. While various methods exist, producing high-purity, spectrally identical single photons on demand, especially at telecommunications wavelengths (crucial for fiber-optic networks), remains a significant challenge. Existing methods often involve complex setups, expensive custom components, or require cryogenic temperatures. Furthermore, scaling up experiments to use multiple identical photon sources has been hindered by the difficulty in fabricating truly indistinguishable sources. This paper addresses the need for a simple, cost-effective, and scalable solution for generating high-quality single photons in the telecom band.

Methods

The core of this work is the use of cross-polarized four-wave mixing (XFWM) in a commercial birefringent optical fiber. Here's a breakdown of the key techniques:

  • XFWM: This non-linear optical process converts two pump photons into a signal and an idler photon. By carefully aligning the pump polarization along the fiber's slow axis and exploiting the fiber's birefringence, the generated signal and idler photons are produced with orthogonal polarizations along the fiber's fast axis. This cross-polarized configuration is crucial for achieving spectral separation and reducing noise.
  • Birefringent Phase Matching: The fiber's birefringence, the difference in refractive indices for light polarized along its two principal axes, is exploited to engineer the phase-matching conditions. This allows for precise control over the wavelengths of the generated signal and idler photons, enabling them to be spectrally separated from the pump.
  • Joint Spectral Intensity (JSI) Measurements: The JSI, which describes the probability distribution of signal and idler photon wavelengths, is a key diagnostic tool. By measuring the JSI, the researchers can assess the spectral correlations between the photon pairs. A "factorable" JSI, meaning it can be expressed as a product of independent signal and idler spectra, indicates spectrally pure single photons.
  • Stimulated Emission Tomography (SET): This technique is used to measure the JSI and characterize the fiber's homogeneity. By seeding the FWM process with a weak continuous-wave laser, the researchers can amplify the generated photons, making them easier to detect and analyze.
  • Second-Order Coherence (g⁽²⁾(τ)) Measurements: These measurements are used to quantify the "single-photonness" of the source. A value of g⁽²⁾(0) close to zero indicates that the source emits at most one photon at a time, a hallmark of a true single-photon source.

Datasets

Not discussed in the paper. The experiments rely on measurements of photon counts and spectral properties, rather than pre-existing datasets.

Key Insights and Ideas

  • Commercial Fiber as a High-Quality Source: The most significant insight is that a standard, commercially available birefringent optical fiber (PM980-XP) can be used to generate high-purity single photons, challenging the notion that specialized or custom-fabricated components are always necessary.
  • Birefringence as a Tunable Control Knob: The paper demonstrates how the inherent birefringence of the fiber can be precisely controlled to achieve phase matching for XFWM, leading to spectrally distinct signal and idler photons.
  • Fiber Homogeneity for Scalability: The investigation into fiber homogeneity revealed that the commercial fiber is remarkably uniform over significant lengths (at least 45 cm). This is a critical finding, as it suggests the potential to create multiple, identical single-photon sources from a single batch of fiber, a major step towards scalable quantum experiments.
  • Telecom Wavelengths Achieved Cost-Effectively: The ability to generate photons in the O-band (1260-1360 nm) is crucial for integration with existing fiber-optic infrastructure, and doing so with a low-cost fiber is a significant practical advantage.

Key Results

  • Purity: The source achieves a spectral purity of 85%.
  • Heralding Efficiency: A heralding efficiency of 30% was demonstrated.
  • Coincidence-to-Accidentals Ratio (CAR): A CAR of 108 was measured, indicating a very low level of noise and a high correlation between heralded and detected photons.
  • Fiber Homogeneity: The fiber was found to be homogeneous over at least 45 cm, suggesting the potential to create at least 4 identical sources.
  • Telecom Wavelengths: Single photons were generated in the telecom O-Band (specifically at 1310 nm for the idler photon).
  • Tunability: The source is tunable, with the potential to generate photons in the C-band (around 1550 nm) also demonstrated.

Limitations and Future Work

  • Factorability Trade-off: While the JSI measurements show good agreement with theoretical predictions, the paper notes that increasing the pump bandwidth to improve signal levels can lead to a slight decrease in factorability. Future work could focus on optimizing pump filtering to restore full factorability.
  • Seed Laser Calibration: The paper mentions that discrepancies in JSI measurements can arise from the stability and calibration of the tunable seed laser used for seeded FWM. Improving the seed laser setup could lead to more precise JSI characterization and potentially higher overlap between sources.
  • Scalability to More Sources: While homogeneity over 45 cm suggests the possibility of 4 sources, further investigation into longer fiber lengths and batch-to-batch consistency would be beneficial for realizing larger multi-photon experiments.
  • Integration with Other Platforms: The authors highlight that the fiber-based nature of the source makes it well-suited for integration with integrated photonic circuits, which could be a key area for future research.
  • Exploring Other Telecom Bands: The demonstration of C-band generation opens doors for exploring other telecom wavelengths and applications.

Summary updated

Abstract

We report a bright and tunable source of spectrally pure heralded single photons in the telecom O-Band, based on cross-polarized four wave mixing in a commercial birefringent optical fiber. The source can achieve a purity of 85%, heralding efficiency of 30% and a coincidence-to-accidentals ratio of 108. Furthermore, through the measurements of joint spectral intensities, we find that the fiber is homogeneous over at least 45 centimeters and thus can potentially realize 4 sources that can produce identical quantum states of light. This paves the way for a cost-effective fiber-optic approach to implement multi-photon quantum optics experiments.
BibTeX
@inproceedings{lugani2020spectrally,
  author = {Jasleen Lugani and Robert J. A. Francis-Jones and Joelle Boutari and Ian A. Walmsley},
  title = {{Spectrally pure single photons at telecommunications wavelengths using commercial birefringent optical fiber}},
  booktitle = {Optics Express},
  year = {2020},
  doi = {10.1364/oe.383704},
}
Figure