Silicon-On-Insulator Lateral Dual Sidewall Schottky (SOI-LDSS) Concept for Improved Rectifier Performance: A Two-Dimensional Simulation Study

M. Jagadesh Kumar, Linga Reddy Cenkeramaddi

Abstract

In this paper, we demonstrate that the performance of silicon Schottky rectifiers on SOI can be significantly improved using a Lateral Dual Sidewall Schottky (LDSS) concept. Our results based on numerical simulation show that the LDSS structure on SOI has low forward voltage drop and low reverse leakage current while its breakdown voltage is significantly larger than that of a conventional Schottky rectifier.

Introduction

Schottky rectifiers are essential components in modern power electronics, particularly in switched-mode power supplies, because they lack the "reverse recovery" issues found in standard P-N junction diodes. However, they face a fundamental design compromise: low-barrier metals (like Nickel) provide a low forward voltage drop but suffer from high leakage current and low breakdown voltages, while high-barrier metals (like Tungsten) offer low leakage at the cost of reduced efficiency.

When integrated into Silicon-On-Insulator (SOI) technology, lateral designs often exacerbate electric field crowding at contact edges, leading to premature device failure. This study proposes a "Lateral Dual Sidewall Schottky" (LDSS) structure to achieve the "best of both worlds" in a lateral SOI format.

Device Structure and Simulation Methods

The study utilizes two-dimensional numerical simulation using the MEDICI simulator. The core innovation is the LDSS structure, which features a dual-metal anode within a trench architecture.

Cross-sectional view of the proposed Lateral Dual Sidewall Schottky (LDSS) structure on SOI.

As shown in the figure above, the design incorporates:

  • Dual-Metal Anode: Nickel (low-barrier, $\phi_{BL} = 0.57$ eV) and Tungsten (high-barrier, $\phi_{BH} = 0.67$ eV).
  • Trench Geometry: The high-barrier metal (HBS) is placed in a deeper trench ($0.4 \mu m$), while the low-barrier metal (LBS) occupies a shallower trench ($0.1 \mu m$).
  • Field Plate: A $3.5 \mu m$ field plate manages electric field distribution.

The LDSS performance was benchmarked against a Lateral Conventional Schottky (LCS) rectifier using identical dimensions and doping profiles.

Cross-sectional view of the conventional Lateral Conventional Schottky (LCS) rectifier.

Key Insights and Results

The LDSS design leverages a "pinch-off" effect. In reverse bias, the depletion regions from the deeper high-barrier metal sidewalls meet and shield the low-barrier metal from high electric fields. This ensures that the leakage current is dictated by the high-barrier metal. Additionally, the peak electric field is shifted away from the Schottky interface toward the edge of the field plate.

Performance Comparison

  • Breakdown Voltage: The LDSS structure achieved a breakdown voltage of approximately 60V, representing a 3x improvement over the ~20V observed in the conventional LCS structure.
  • Forward Characteristics: The forward current density of the LDSS was nearly identical to a pure Nickel rectifier, maintaining high efficiency.
  • Leakage Current: Reverse leakage was significantly lower than conventional low-barrier rectifiers, aligning with high-barrier Tungsten device performance.
  • Sharp Breakdown: Unlike conventional devices with "soft" leakage increases, the LDSS showed a very sharp, well-defined breakdown point.

Conclusion

The LDSS concept effectively allows a device to "change its identity" based on bias: under forward bias, the low-barrier metal dominates conduction for low loss; under reverse bias, the high-barrier metal dominates blocking for high reliability. While simulation results are promising, physical fabrication of dual-metal trenches with precise sub-micron depths presents manufacturing challenges. Future work should focus on experimental prototyping and modeling thermal effects on SOI substrates.

Summary updated

Abstract

In this paper, we demonstrate that the performance of silicon Schottky rectifiers on SOI can be significantly improved using a Lateral Dual Sidewall Schottky (LDSS) concept. Our results based on numerical simulation show that the LDSS structure on SOI has low forward voltage drop and low reverse leakage current while its breakdown voltage is significantly larger than that of a conventional Schottky rectifier.
BibTeX
@inproceedings{kumar2006silicon,
  author = {M. Jagadesh Kumar and Linga Reddy Cenkeramaddi},
  title = {{Silicon-On-Insulator Lateral Dual Sidewall Schottky (SOI-LDSS) Concept for Improved Rectifier Performance: A Two-Dimensional Simulation Study}},
  booktitle = {Microelectronics},
  year = {2006},
  doi = {10.1108/13565360610642705},
}

Loading related content...

Figure