RF Power Transmission for Self-sustaining Miniaturized IoT Devices

Lukas Schulthess, Federico Villani, Philipp Mayer, Michele Magno

TL;DR

This paper presents a highly efficient RF wireless power transfer (WPT) subsystem for miniaturized IoT devices, achieving over 30% overall power conversion efficiency (PCE) at -10 dBm input power. This advancement is crucial for enabling truly battery-less and self-sustaining IoT applications by overcoming the limitations of current energy harvesting technologies.

What Problem Does This Paper Address?

The proliferation of Internet of Things (IoT) devices is creating a demand for reliable and sustainable power sources. Traditional batteries require frequent replacement, which is impractical for many IoT deployments, especially in remote or inaccessible locations. While environmental energy harvesting (solar, thermal, vibration) offers a renewable solution, its unpredictable nature makes it unsuitable for applications requiring consistent power. Radio Frequency (RF) wireless power transfer (WPT) presents a promising alternative, offering controllable and potentially long-distance power delivery. However, a significant challenge lies in achieving high conversion efficiency, particularly for miniaturized IoT devices that require small antennas and operate at low input power levels (often below -10 dBm). This paper addresses the need for an efficient RF WPT subsystem that can reliably power these devices, even from weak RF signals, and manage harvested energy effectively.

Methods

The authors propose a three-block RF wireless power energy conversion system: an impedance matching network (IMN), a rectifier, and a power management unit with energy storage.

  • Impedance Matching Network (IMN): The IMN is designed to transform the low impedance of the antenna to the system impedance, minimizing power reflections and losses. They utilize high-Q discrete components to achieve this.
  • Rectifier: A critical component for efficient RF-to-DC conversion, the rectifier employs zero-bias Schottky diodes (BAT15-04W) in a voltage doubler configuration. This choice is motivated by the diodes' low threshold voltage and junction capacitance. The circuit is realized on a 2-layer PCB with RO4003c dielectric for good high-frequency performance.
  • Power Management with Energy Storage: To handle the non-constant power demands of IoT devices, a power management IC (E-PEAS AEM30940) is integrated. This IC can operate from very low input voltages and powers, storing energy in a capacitor before providing a stable output voltage via internal buck and LDO regulators. It also includes features like maximum power point tracking (MPPT) and a cold-start capability.

The proposed system is tuned for a center frequency of 915 MHz, a common frequency for WPT. Experimental validation compares the custom-designed frontend against commercially available "e-peas HP" and "e-peas LP" solutions.

Datasets

Not discussed in the paper. The paper focuses on experimental characterization and evaluation of the proposed hardware subsystem.

Key Insights and Ideas

  • Custom RF Frontend Outperforms Commercial Solutions at Low Power: The custom-designed RF frontend, despite using off-the-shelf components, demonstrates superior rectification efficiency compared to commercial "e-peas HP" and "e-peas LP" solutions for input power levels between -11 dBm and 5 dBm. This is a significant finding for enabling battery-less operation from weaker RF sources.
  • Importance of Careful Component Selection and PCB Design: The paper highlights how the selection of high-Q components for the IMN and rectifier, along with the use of a suitable PCB dielectric (RO4003c), is crucial for achieving high efficiency in RF harvesting.
  • Integrated Power Management is Key for IoT: The inclusion of a sophisticated power management IC like the AEM30940 is essential. It not only manages harvested energy but also provides critical features like MPPT and a robust cold-start mechanism, enabling devices to wake up even from a completely discharged state.
  • Cold-Start Capability is Critical for Intermittent Devices: The experimental demonstration of the cold-start sequence shows that the system can successfully power up and reach normal operation from a very low input power (-15 dBm) after a period of charging and stabilization, a vital characteristic for self-sustaining devices.

Key Results

  • Overall Power Conversion Efficiency (PCE): The proposed subsystem achieved an overall PCE of over 30% for an input power of -10 dBm.
  • Peak Efficiency: A peak efficiency of 57% was achieved at an input power of 3 dBm.
  • Rectification Efficiency: The custom rectifier showed up to 20% efficiency gain compared to commercial circuits for input power levels between -12 dBm and 9 dBm.
  • Low-Power Operation: The "e-peas LP" frontend enabled energy-positive operation down to -15 dBm, while the custom and "e-peas HP" frontends reached -16 dBm and -15 dBm, respectively.
  • Cold-Start Performance: The system, when combined with the AEM30940 IC, was able to exit cold start after 56 seconds from an input power as low as -15 dBm.

Limitations and Future Work

  • Narrowband Operation: The proposed custom RF frontend is optimized for a narrow band at 915 MHz. While this is suitable for specific applications, future work could explore broadband matching networks to harvest energy from a wider range of frequencies and signals.
  • Miniaturized Antenna Integration: The paper mentions the need for miniaturized antennas but focuses on the rectifier and power management. Further research could integrate the proposed frontend with highly efficient, miniaturized antennas for a complete self-sustaining IoT node.
  • Distance Limitations: While RF WPT offers longer ranges than inductive coupling, the power levels decrease significantly with distance. Future work could explore techniques for improving power delivery efficiency over longer distances or investigate multi-hop WPT systems.

Summary updated

Abstract

Radio Frequency (RF) wireless power transfer is a promising technology that has the potential to constantly power small Internet of Things (IoT) devices, enabling even battery-less systems and reducing their maintenance requirements. However, to achieve this ambitious goal, carefully designed RF energy harvesting (EH) systems are needed to minimize the conversion losses and the conversion efficiency of the limited power. For intelligent internet of things sensors and devices, which often have non-constant power requirements, an additional power management stage with energy storage is needed to temporarily provide a higher power output than the power being harvested. This paper proposes an RF wireless power energy conversion system for miniaturized IoT composed of an impedance matching network, a rectifier, and power management with energy storage. The proposed sub-system has been experimentally validated and achieved an overall power conversion efficiency (PCE) of over 30 % for an input power of -10 dBm and a peak efficiency of 57 % at 3 dBm.
BibTeX
@inproceedings{schulthess2022rf,
  author = {Lukas Schulthess and Federico Villani and Philipp Mayer and Michele Magno},
  title = {{RF Power Transmission for Self-sustaining Miniaturized IoT Devices}},
  booktitle = {Icecs},
  year = {2022},
  doi = {10.1109/icecs202256217.2022.9970865},
}
Figure