Research on the Influence of Exhaust Temperatures on the Emission Performance of Urea-SCR After-treatment System

Jing Wang, Qian Wang, Licheng Wu, Wei Zhao, Shuo Li2016 · DOI

Abstract: SCR (Selective Catalytic Reduction) technology is the most effective after-treatment technology of DeNOx on vehicle diesel engines. In this paper, a modeling of vehicle diesel Urea-SCR after-treatment system was set up with the method of CFD coupled with chemical reaction dynamic, to make a full-scale simulation and comparison of two Urea-SCR catalyst systems, analyzing the influences of different exhaust temperatures on the emission performance of SCR system, so as to better improve the design of SCR system.

Introduction

Nitrogen oxides (NOx) from diesel engines are a primary atmospheric pollutant, and Selective Catalytic Reduction (SCR) is the industry-standard "after-treatment" solution. In an SCR system, a urea solution is sprayed into the exhaust stream, decomposing into ammonia (NH₃), which then reacts with NOx over a catalyst to produce harmless nitrogen and water.

However, SCR performance is highly sensitive to two factors:

  1. Exhaust Temperature: If it’s too cold, the urea doesn't evaporate or react; if it’s too hot, the ammonia oxidizes prematurely or the catalyst degrades.
  2. Flow Uniformity: If the urea spray doesn't mix evenly with the exhaust gas, it results in "ammonia slip" (leaking unreacted NH₃) and poor NOx reduction.

This study utilizes 3D Computational Fluid Dynamics (CFD) to model how these factors dictate system efficiency across different architectural designs.

Methodology

The researchers employed AVL FIRE, a specialized CFD platform, to conduct full-scale 3D numerical simulations. Their modeling approach combined several complex sub-models, including the Discrete Droplet Model (DDM) for tracking urea droplets and the HuhGosman Break-up Model to simulate droplet shattering. The catalyst was treated as a single-direction porous medium using the Forchheimer model to calculate pressure loss.

The study compared two specific designs based on a 6.5L six-cylinder diesel engine:

  • Plan One: A standard three-hole nozzle setup.
  • Plan Two: A more advanced four-hole nozzle combined with a perforated diffuser (a cylinder with many 8mm holes) designed to force better mixing.
Design schematic of Plan Two featuring a perforated diffuser for enhanced mixing.

Results and Discussion

The simulation results reveal that NOx conversion efficiency follows a parabolic arc. Initially, rising temperatures accelerate urea thermolysis and catalytic activity. However, once temperatures exceed 400°C–450°C, efficiency drops because the ammonia starts reacting with oxygen (oxidation) instead of the NOx.

The most striking insight is the performance gap between the two designs. Plan Two significantly outperformed Plan One due to the mechanical "rebound" effect. When urea droplets hit the enclosed bottom of the diffuser, the inertia of the exhaust gas causes them to shatter into a much finer mist than a simple nozzle can achieve. This leads to a more uniform concentration of reductant across the catalyst face.

NOx conversion efficiency vs. temperature for (a) Plan One and (b) Plan Two.

As shown in the efficiency curves, Plan One reached a maximum NOx conversion efficiency of 66% at 400°C. In contrast, Plan Two reached a maximum efficiency of 94% at 450°C. By using the diffuser to create forced turbulence and "small whirlpools," the system ensured that the catalyst was used more effectively across its entire volume.

Conclusion

The inclusion of a perforated diffuser in the SCR system design dramatically improves NOx conversion efficiency by optimizing droplet breakup and flow uniformity. While these CFD results are compelling, future work should include experimental validation to confirm these findings in real-world conditions and assess the long-term durability of the diffuser design against potential soot accumulation.

Summary updated

Abstract

SCR (Selective Catalytic Reduction) technology is the most effective after-treatment technology of DeNOx on vehicle diesel engines. In this paper, a modeling of vehicle diesel Urea-SCR after-treatment system was set up with the method of CFD coupled with chemical reaction dynamic, to make a full-scale simulation and comparison of two Urea-SCR catalyst systems, analyzing the influences of different exhaust temperatures on the emission performance of SCR system, so as to better improve the design of SCR system.
BibTeX
@misc{wang2016research,
  author = {Jing Wang and Qian Wang and Licheng Wu and Wei Zhao and Shuo Li},
  title = {{Research on the Influence of Exhaust Temperatures on the Emission Performance of Urea-SCR After-treatment System}},
  year = {2016},
  doi = {10.2991/mmeceb-15.2016.89},
}
Measures to Comply with NOx Emission Tier III and Machinery Outfitting (SCR)Marine · 2018
Activating low-temperature diesel oxidation by single-atom Pt on TiO2 nanowire arrayNature Communications · 2020
DE2-3: In-cylinder Stratification of External EGR Gas for Diesel Combustion(DE: Diesel Engine Combustion,General Session Papers)The Proceedings of the International Symposium on Diagnostics and Modeling of Combustion in Internal Combustion Engines · 2008
A NEW DRAG REDUCTION METHOD BASED ON EXHAUST EMISSION TRAILING VORTEX CONTROLInternational Journal of Mechatronics and Applied Mechanics · 2019
Aerothermal predictions of combustor/turbine interactions using advanced turbulence modelingProceedings of ... European Conference on Turbomachinery Fluid Dynamics & Thermodynamics · 2019
Structural simulation analysis of high pressure common rail pipeVibroengineering · 2021
Figure