Research on size coupling and sensitivity analysis of SAR antenna truss rod

Yun Li, Ting Zeng, Ling Chen, Zhiqiang Zhang, Jianze Liu, Lihui ChenJournal of Physics Conference Series 2022 · DOI

Abstract

To eliminate the influence of the size coupling of SAR antenna truss rod on assembly accuracy, this paper defines the assembly sequence, part datum, tolerance, assembly operation, and measurement operation of the model by establishing the tolerance analysis model of the assembly dimension chain and measurement target. The assembly simulation process of the deployment mechanism is simulated, the plane deviation of the antenna panel of the deployment mechanism is analyzed, and the contribution and sensitivity data of each component ring size to the closed ring size are obtained. The simulation results show that the in-plane angle error of the antenna panel is mainly affected by the length of the component ring rod. By focusing on controlling the dimensional tolerance of the truss rods with high sensitivity, the assembly accuracy of the antenna deployment system can be guaranteed. Sensitivity is the magnification of assembly deviation by the transmission of deviation source, which reflects the influence of the change of composition tolerance on the change of functional requirements. According to the sensitivity analysis, the key dimensions that affect assembly accuracy can be obtained. The assembly requirements of high-quality and low-cost products can be achieved by strictly controlling the dimensional tolerance of key components and relaxing the tolerance of non-key components.

Introduction

As satellite missions become more ambitious, Synthetic Aperture Radar (SAR) antennas are growing larger and more complex. These antennas rely on deployable space truss mechanisms—intricate webs of rods and hinges that must unfold perfectly in orbit. The primary challenge in manufacturing these systems is "size coupling": the final pointing accuracy and flatness of the antenna are not simply the sum of individual part errors. Because the rods and hinges interact in a complex, non-linear fashion, it is difficult for engineers to predict which manufacturing tolerances matter most.

Traditionally, tolerance allocation has relied on experience, often leading to over-engineering (which is expensive) or unexpected assembly errors (which degrade performance). This research presents a systematic method for optimizing the assembly accuracy of these systems using tolerance dimension chains and sensitivity analysis.

Methodology

The researchers developed a simulation-based approach to map how individual part variations propagate through the entire assembly. This involved creating a simplified geometric model of the antenna mechanism (Figure 1), defining a "dimension chain" that links individual rod lengths and hinge locking angles to the final orientation of the antenna panels.

Figure 1. Simplified model of the antenna deployment system showing the truss rod dimension chain.

The team simulated the assembly process using the 3-2-1 positioning principle to ensure the model reflected real-world manufacturing steps. They then calculated the sensitivity of the final assembly to each variable using a partial derivative approach, measuring how much the final antenna angle changed when a single rod's length was slightly varied. Finally, a contribution analysis was performed to determine which parts were responsible for the bulk of the final alignment error.

Key Insights and Results

The study reveals that not all components are created equal. Sensitivity acts as a "magnification" effect; a rod with high sensitivity will amplify a tiny manufacturing error into a significant pointing error at the end of the deployment chain. Conversely, "non-key" components with low sensitivity can have their tolerances relaxed to save costs without compromising quality.

Critical Components

The simulation provided concrete data on the drivers of antenna misalignment:

  • Inner Plate Error: Rod L3 was the dominant factor, contributing 38.8% to the angular error.
  • Outer Plate Error: Rod L7 was the primary driver, contributing 39.22% to the error.
  • Relative Flatness: When looking at the relative angle between the inner and outer plates—crucial for radar performance—rods L4 and L5 were the most influential, each contributing roughly 30.23% to the total error.
Figure 4. Statistical distribution of the relative angle error between the inner and outer antenna plates.

In contrast, hinge locking angles (such as Hinge D) showed very low sensitivity (0.52% contribution), suggesting that standard manufacturing precision is more than sufficient for these parts.

Conclusion

By identifying the key dimensions that disproportionately affect assembly accuracy, manufacturers can focus precision efforts where they matter most. While this study uses a simplified geometry and does not yet account for environmental factors like thermal expansion in space, it provides a robust framework for achieving high-quality, low-cost aerospace assemblies through selective precision.

Summary updated

Abstract

Abstract To eliminate the influence of the size coupling of SAR antenna truss rod on assembly accuracy, this paper defines the assembly sequence, part datum, tolerance, assembly operation, and measurement operation of the model by establishing the tolerance analysis model of the assembly dimension chain and measurement target. The assembly simulation process of the deployment mechanism is simulated, the plane deviation of the antenna panel of the deployment mechanism is analyzed, and the contribution and sensitivity data of each component ring size to the closed ring size are obtained. The simulation results show that the in-plane angle error of the antenna panel is mainly affected by the length of the component ring rod. By focusing on controlling the dimensional tolerance of the truss rods with high sensitivity, the assembly accuracy of the antenna deployment system can be guaranteed. Sensitivity is the magnification of assembly deviation by the transmission of deviation source, which reflects the influence of the change of composition tolerance on the change of functional requirements. According to the sensitivity analysis, the key dimensions that affect assembly accuracy can be obtained. The assembly requirements of high-quality and low-cost products can be achieved by strictly controlling the dimensional tolerance of key components and relaxing the tolerance of non-key components.
BibTeX
@article{li2022research,
  author = {Yun Li and Ting Zeng and Ling Chen and Zhiqiang Zhang and Jianze Liu and Lihui Chen},
  title = {{Research on size coupling and sensitivity analysis of SAR antenna truss rod}},
  journal = {Journal of Physics Conference Series},
  year = {2022},
  doi = {10.1088/1742-6596/2390/1/012091},
}
Figure