Preparation of Spherical Alumina Powder by RF Thermal Plasma: Numerical Simulation and Experimentation

Wenbo Chen, Lun-Jiang Chen, Chuandong Liu, Cheng Chang-ming, Honghui Tong, Hailong ZhuJournal of Inorganic Materials 2018 · DOI

Abstract: Behavior of alumina powder particles in inductively coupled thermal plasma (ICTP) can provide theoretical reference and guidelines for improving preparation process of plasma spheroidization. In this study, the motion trajectories and heating process of alumina powder particles in ICTP were investigated by means of numerical simulation with FLUENT software. Then the plasma spheroidization experiment was carried out on the basis of simulation results, and the effect of input power, powder feeder rate and particle size distribution on alumina powder spheroidization were studied by combination of experimental and the theoretical analyses. The results show that the small particles absorb enough heat from thermal plasma and therefore be heated to completely melt. Furthermore, the particle can get more energy from plasma while the input power of system is increased or the powder feeder rate is decreased, which improve the spheroidization effect of alumina powder particles.

Introduction

Spherical alumina ($Al_2O_3$) powder is highly valued in aerospace and chemical engineering for its superior flowability, high packing density, and uniform stress distribution. Producing these micro-spheres efficiently requires precise control over Radio Frequency (RF) inductively coupled thermal plasma (ICTP). The extreme environment inside a plasma torch—where temperatures can exceed 10,000 K—makes experimental trial-and-error both difficult and costly. This study utilizes a combination of numerical simulations and physical experiments to optimize the spheroidization process.

Methodology

The research team employed a dual-pronged approach to map particle behavior. Numerical simulations were performed using FLUENT software, incorporating Magnetic Vector Potential to account for electromagnetic fields and a Discrete Phase Model (DPM) to track individual alumina particles.

Schematic diagram of the RF plasma spheroidization system and torch geometry.

Experimentally, a custom-built RF plasma system was used to process alumina powders with mean diameters of 25 μm and 45 μm. The system parameters, including input power (56–70 kW) and powder feed rates (6.0–96.0 g/min), were varied to observe their impact on the final product's morphology.

Results and Discussion

Thermal Behavior and Particle Size

A critical finding was the relationship between particle size and thermal history. Smaller particles (20–30 μm) are more easily influenced by the plasma's flow field, often deviating toward hotter regions near the torch walls. This increased residence time allows them to reach boiling temperatures, ensuring complete melting. In contrast, larger particles (40–50 μm) reach their melting point but often fail to vaporize or melt uniformly through the core, sometimes resulting in surface cracks during rapid cooling.

Particle mean temperature profiles along the torch axis (Z) for different particle size distributions.

Optimization of Spheroidization Rate

The study identified a "Goldilocks zone" for high-quality production. For 25 μm powder at a feed rate of 35 g/min and 56 kW of power, the team achieved a spheroidization rate exceeding 95%. However, increasing the feed rate to 65.7 g/min caused the rate to plummet below 60%. This is due to the "quenching effect," where high concentrations of powder absorb excessive heat, cooling the surrounding plasma and preventing complete melting of the remaining particles.

Conclusion

Spheroidization efficiency is fundamentally an energy-per-unit-mass balance. Increasing system power or decreasing the powder feed rate enhances the energy available to each particle, directly improving roundness. While smaller particles are easier to spheroidize, future work is needed to refine the quenching process for larger particles to eliminate surface cracking and improve overall yield. This research provides a robust theoretical framework for scaling RF plasma spheroidization to industrial levels.

Summary updated

Abstract

Behavior of alumina powder particles in inductively coupled thermal plasma (ICTP) can provide theoretical reference and guidelines for improving preparation process of plasma spheroidization. In this study, the motion trajectories and heating process of alumina powder particles in ICTP were investigated by means of numerical simulation with FLUENT software. Then the plasma spheroidization experiment was carried out on the basis of simulation results, and the effect of input power, powder feeder rate and particle size distribution on alumina powder spheroidization were studied by combination of experimental and the theoretical analyses. The results show that the small particles absorb enough heat from thermal plasma and therefore be heated to completely melt. Furthermore, the particle can get more energy from plasma while the input power of system is increased or the powder feeder rate is decreased, which improve the spheroidization effect of alumina powder particles.
BibTeX
@article{chen2018preparation,
  author = {Wenbo Chen and Lun-Jiang Chen and Chuandong Liu and Cheng Chang-ming and Honghui Tong and Hailong Zhu},
  title = {{Preparation of Spherical Alumina Powder by RF Thermal Plasma: Numerical Simulation and Experimentation}},
  journal = {Journal of Inorganic Materials},
  year = {2018},
  doi = {10.15541/jim20170266},
}
Figure