Abstract
In future wireless systems, a large number of users may access the networks via moving relays (MRs) installed on top of vehicles. One of the main challenges of MRs is rapid channel variation which may make channel estimation, and its following procedures, difficult. To address these issues, various schemes are designed, among which predictor antenna (PA) is a candidate. The PA setup refers to a system with two (sets of) antennas on top of a vehicle, where the PA(s) positioned in front of the vehicle is(are) utilized to predict the channel state information required for data transmission to the receive antennas (RAs) aligned behind the PA. In this paper, we introduce the concept and the potentials of PA systems. Moreover, summarizing the field trials for PAs and the 3GPP attempts on (moving) relays, we compare the performance of different PA and non-PA methods for vehicle communications in both urban and rural areas with the PA setup backhauled through terrestrial or satellite technology, respectively. As we show, with typical parameter settings and vehicle speeds, a single-antenna PA-assisted setup can boost the backhaul throughput of MRs, compared to state-of-the-art open-loop schemes, by up to 50%.
Introduction
In modern wireless networks, users in high-speed vehicles such as trains, buses, and cars often experience degraded connectivity. Moving Relays (MRs)—access points mounted on vehicle roofs that bridge the gap between external base stations and internal users—are a key solution. However, at high speeds, MRs face the critical challenge of Channel Aging. By the time a base station estimates the radio channel and prepares a data packet, the vehicle has moved, rendering the Channel State Information (CSI) obsolete. While current 4G/5G systems perform well for pedestrians, their efficiency drops significantly at speeds above 120 km/h because they cannot accurately predict these fast-changing environments.
The Predictor Antenna Concept
The Predictor Antenna (PA) system is a hardware-based solution to the channel aging problem. The setup involves installing two sets of antennas on the vehicle roof: the Predictor Antenna (PA) is placed at the front, and the Receive Antennas (RAs) are aligned behind it along the direction of travel.
As the vehicle moves, the PA samples the channel at a specific spatial point. Since the RAs follow the same path, they reach that exact spatial point a few milliseconds later. By using the PA’s measurements, the system provides the base station with "future" CSI for the RAs, effectively looking ahead in time. The system can operate in an adaptive-delay mode, adjusting transmission timing based on vehicle speed, or a nonadaptive-delay mode using spatial interpolation when perfect alignment isn't possible.
Performance Analysis and Key Results
The effectiveness of the PA system was evaluated using numerical simulations based on Jakes’ correlation models for urban areas and shadowed Rice models for rural/satellite scenarios. Results indicate that the PA system significantly extends the prediction horizon compared to traditional mathematical methods like Kalman filters.
Key findings include:
- Throughput Gains: As shown in Figure 2, a single-antenna PA setup can increase backhaul throughput by up to 50% compared to standard open-loop (non-CSI) schemes. The "adaptive delay" approach maintains peak performance by minimizing spatial mismatch.
- Superior Speed Support: At a carrier frequency of 2.68 GHz and a 5ms delay, the PA system supports vehicle speeds up to 120 km/h, whereas traditional Kalman predictors fail past 24 km/h.
- Robustness via Massive MIMO: When combined with Massive MIMO beamforming, the system becomes more robust to spatial mismatches. The beamforming helps "blur" small physical misalignments between the PA's sampled point and the RA's actual position.
- Rural Reliability: In rural train simulations, the PA system effectively neutralized channel aging, maintaining nearly constant Quality of Service (QoS) even when tree foliage or buildings caused intermittent shadowing.
Discussion and Future Work
While the PA system offers substantial gains, several challenges remain for widespread adoption. Integrating PA into current 3GPP standards for Integrated Access and Backhaul (IAB) requires updates to mobility handling. Furthermore, as the industry moves toward millimeter wave (mmWave) frequencies, beamforming will become even more sensitive to spatial mismatch, requiring higher precision in PA timing and synchronization. Future work will focus on implementing real-time, high-precision speed tracking to support these adaptive-delay mechanisms in diverse hardware configurations.
Summary updated