Performance of Magnetic Quantum Cellular Automata and Limitations due to Thermal Noise

Federico M. Spedalieri, Ajey P. Jacob, Dmitri E. Nikonov, Vwani Roychowdhury

Performance of Magnetic Quantum Cellular Automata and Limitations due to Thermal Noise

Abstract Operation parameters of magnetic quantum cellular automata (MQCA) are evaluated for the purposes of reliable logic operation. The dynamics of the nanomagnets is simulated via the Landau-Lifshitz-Gilbert (LLG) equations with a stochastic magnetic field corresponding to thermal fluctuations. It is found that in the macrospin approximation, the switching speed does not change under scaling of both size and distances between nanomagnets. Thermal fluctuations put a limitation on the size of nanomagnets, as the gate error rate becomes excessive for nanomagnets smaller than 200 nm at room temperature.

Introduction

As silicon-based CMOS transistors approach their physical and thermodynamic scaling limits, researchers are investigating "beyond-CMOS" logic paradigms. Magnetic Quantum Cellular Automata (MQCA) is a leading candidate, utilizing the magnetic orientation of bistable nanomagnets to represent bits (0 and 1). Logic operations are performed via dipole-dipole interactions between neighboring magnets. However, the viability of MQCA depends on its speed, energy efficiency, and resilience to thermal noise—the random fluctuations of magnetic moments at room temperature. This study establishes fundamental performance bounds for MQCA regarding size, speed, and energy dissipation.

Methodology

The researchers employed a macrospin model, assuming each nanomagnet behaves as a single, uniform magnetic moment. The system's dynamics were simulated using the Landau-Lifshitz-Gilbert (LLG) equations, augmented with a stochastic thermal field (a Langevin approach) to account for temperature. A mid-point numerical method was used for discretization to ensure physical consistency, such as preserving magnetization magnitude over time. Additionally, biaxial anisotropy was introduced to act as a "latch," stabilizing the magnets' initial states before computation begins.

Material and Dimensional Constraints

The study evaluated common magnetic materials, including Permalloy ($Ni_{80}Fe_{20}$), Cobalt Iron Boron (CoFeB), and Iron (Fe). The choice of material significantly impacts the physical dimensions required for stability.

Figure 1: Relationship between thickness and width for different magnetic materials to maintain a specific stability threshold.

Materials with higher saturation magnetization, such as Iron, allow for smaller volumes while maintaining the same stability barrier compared to Permalloy or CoFeB. This relationship is critical for determining the minimum footprint of MQCA logic gates.

Thermal Limits and Reliability

A critical finding is the "thermal wall" facing MQCA. To achieve CMOS-like reliability (an error rate of approximately $10^{-17}$), a nanomagnet requires an energy barrier of at least 1 eV ($\approx 40 k_B T$). While biaxial anisotropy can provide this stability, there is a trade-off: if the anisotropy is too weak, thermal noise causes errors; if it is too strong, the magnetic "signal" from neighbors cannot flip the bit, and the gate "freezes."

Figure 2: Error rate probabilities as a function of nanomagnet thickness and width, illustrating the scaling challenges for reliable operation.

The simulations indicate that for room-temperature operation, the "window" for reliable logic disappears for nanomagnets smaller than 200 nm. Below this threshold, the error rate exceeds 1%, which is far too high for modern computing standards.

Key Performance Results

  • Scaling Invariance: In the macrospin approximation, switching speed remains constant if the magnet size and inter-magnet distances are scaled proportionally. This differs from CMOS, where miniaturization typically increases speed.
  • Gate and Propagation Speed: A typical majority gate reaches 90% of its final state in approximately 700 picoseconds. Information propagates through a chain of magnets at roughly 100 m/s—nearly six orders of magnitude slower than electrical signals in copper wire ($10^7$ m/s).
  • Energy Dissipation: MQCA could theoretically operate with energy dissipation as low as 1 eV per magnet, thousands of times less than CMOS. However, the practical challenge lies in the precise delivery of such small energy amounts.

Conclusion and Future Work

While MQCA offers extreme energy efficiency, it faces significant hurdles in speed and scalability. The 200 nm size limit at room temperature poses a challenge for high-density integration. Future research may need to explore micromagnetic effects beyond the macrospin model, adiabatic switching regimes, or lower operating temperatures to overcome these thermal and speed limitations. The extremely slow propagation speed also suggests that MQCA may struggle with long-distance communication on-chip compared to traditional interconnects.

Summary updated

Abstract

Operation parameters of magnetic quantum cellular automata are evaluated for the purposes of reliable logic operation. The dynamics of the nanomagnets is simulated via the Landau-Lifshitz-Gilbert equations with a stochastic magnetic field corresponding to thermal fluctuations. It is found that in the macrospin approximation the switching speed does not change under scaling of both size and distances between nanomagnets. Thermal fluctuations put a limitation on the size of nanomagnets, since the gate error rate becomes excessive for nanomagnets smaller than 200nm at room temperature.
BibTeX
@article{spedalieri2010performance,
  author = {Federico M. Spedalieri and Ajey P. Jacob and Dmitri E. Nikonov and Vwani Roychowdhury},
  title = {{Performance of Magnetic Quantum Cellular Automata and Limitations due to Thermal Noise}},
  journal = {IEEE Transactions on Nanotechnology},
  year = {2010},
  doi = {10.1109/tnano.2010.2050597},
}
Figure