OS5-1-3 Effects of length scale on plastic deformation instability of Cu/Au multilayers

Y. P. Li, Guangping Zhang, Y. Liu, Jun Tan, Wei WangThe Abstracts of ATEM International Conference on Advanced Technology in Experimental Mechanics Asian Conference on Experimental Mechanics 2007 · DOI

Abstract

Strength and plastic deformation behavior of Cu/Au multilayers with different individual layer thicknesses ranging from submicron to nanometer scale have been studied by using instrumented-indentation. The deformation morphologies around the indents at the sample surfaces and the cross-sections of the multilayers were characterized by scanning electron microscopy (SEM) and focus ion beam. It is found that the hardness increases with decreasing individual layer thickness, and begins to deviate from the Hall-Petch strengthening relationship when the individual layer thickness is less than a certain length scale. Furthermore, significant layer thickness dependent shear banding behavior was observed. Quantitative measurement of the shear band dimensions exhibits that the region of the plastic deformation instability becomes more localized with decreasing the length scale of the multilayers. The mechanisms of strengthening and plastic instability of the material at the nanoscale are discussed.

Introduction

In metallurgy, the Hall-Petch effect describes how smaller grains or thinner layers impede the movement of dislocations, thereby increasing hardness. However, as materials reach the true nanoscale (below 100 nm), this relationship often breaks down. This research investigates the strengthening limits and deformation instability in Cu/Au multilayers, specifically focusing on how layer thickness affects "shear banding"—the localization of strain into narrow zones.

Experimental Methods

Cu/Au multilayers were fabricated using radio-frequency magnetron sputtering on silicon substrates. Four distinct samples were produced with individual layer thicknesses ($\lambda$) of 250, 100, 50, and 25 nm, while maintaining a constant total thickness of 1 μm.

Cross-sectional SEM and TEM images of the Cu/Au multilayers, showing the distinct layering and internal structure.

Mechanical properties were evaluated using nanoindentation with a Berkovich diamond tip and the Continuous Stiffness Measurement (CSM) technique. To visualize internal deformation, Focused Ion Beam (FIB) milling was used to create precise cross-sections through the indents. Surface and internal morphologies were then characterized using Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM).

Strengthening and the Hall-Petch Relationship

The experimental data reveals that the Cu/Au system follows the standard Hall-Petch strengthening law ($H \propto \lambda^{-1/2}$) down to a layer thickness of 50 nm. At 25 nm, the hardness begins to deviate, increasing more slowly than the linear prediction. This shift suggests a transition in the dominant deformation mechanism from dislocation pile-ups at interfaces to single dislocation glide across individual layers.

Plot of hardness versus the inverse square root of layer thickness, showing the Hall-Petch relationship and the deviation at 25 nm.

The interface in Cu/Au is considered "transparent" due to similar crystal structures and (111) textures, allowing dislocations to pass through more easily than in "opaque" systems like Cu/Nb. The measured interface strengthening ability ($k$) for Cu/Au was 14.8 GPa·m$^{-1/2}$, placing it between systems like Cu/Ni and Cu/Nb.

Plastic Deformation Instability

A key finding of this research is the scale-dependent nature of plastic instability. As layer thickness decreases, deformation becomes increasingly localized. While 250 nm layers exhibit gentle "kinking" at interfaces, the 25 nm samples develop sharp, narrow shear bands.

Quantitative analysis showed that the shear band width ($W_{SB}$) decreased from 370 nm for the 250 nm layers to just 73 nm for the 25 nm layers. Notably, in the thinnest layers, the shear band width closely matches the grain size, suggesting that deformation at this scale is driven by grain rotation and boundary sliding rather than conventional dislocation movement.

Conclusion

This study demonstrates that shrinking metallic layers to the nanoscale significantly enhances hardness but also promotes localized plastic instability. The transition from dislocation-mediated plasticity to grain-boundary-mediated processes at approximately 50 nm marks a critical threshold for Cu/Au multilayers. Future research involving in-situ TEM testing and molecular dynamics simulations will be essential to further clarify the exact atomic-scale mechanisms of interface transparency and shear band formation.

Summary updated

Abstract

Strength and plastic deformation behavior of Cu/Au multilayers with different individual layer thicknesses ranging from submicron to nanometer scale have been studied by using instrumented-indentation. The deformation morphologies around the indents at the sample surfaces and the cross-sections of the multilayers were characterized by scanning electron microscopy (SEM) and focus ion beam. It is found that the hardness increases with decreasing individual layer thickness, and begins to deviate from the Hall-Petch strengthening relationship when the individual layer thickness is less than a certain length scale. Furthermore, significant layer thickness dependent shear banding behavior was observed. Quantitative measurement of the shear band dimensions exhibits that the region of the plastic deformation instability becomes more localized with decreasing the length scale of the multilayers. The mechanisms of strengthening and plastic instability of the material at the nanoscale are discussed.
BibTeX
@inproceedings{li2007os,
  author = {Y. P. Li and Guangping Zhang and Y. Liu and Jun Tan and Wei Wang},
  title = {{OS5-1-3 Effects of length scale on plastic deformation instability of Cu/Au multilayers}},
  booktitle = {The Abstracts of ATEM International Conference on Advanced Technology in Experimental Mechanics Asian Conference on Experimental Mechanics},
  year = {2007},
  doi = {10.1299/jsmeatem.2007.6.\_os5-1-3-1},
}
Figure