Multiuser Beamforming for Pinching-Antenna Systems: An Element-wise Optimization Framework

Mingjun Sun, Chongjun Ouyang, Shaochuan Wu, Yuanwei Liu

TL;DR

This paper introduces a low-complexity framework for optimizing Pinching-Antenna Systems (PASS), a novel flexible-antenna technology where antennas can slide along waveguides to "reconstruct" wireless channels. By using an element-wise sequential optimization approach, the authors achieve massive sum-rate gains (up to 190% over fixed-antenna systems) without the heavy computational burden of traditional joint optimization methods.

What Problem Does This Paper Address?

In traditional MIMO (Multiple-Input Multiple-Output) systems, antennas are fixed in place. While digital beamforming can steer signals, it cannot change the physical environment or the inherent path loss between the transmitter and receiver. Emerging "flexible-antenna" technologies like Movable Antennas (MA) and PASS aim to change this by adding a physical degree of freedom: moving the antennas themselves.

However, PASS presents a difficult "chicken-and-egg" optimization problem. To get the best data rate, you need to optimize the baseband beamformer (digital signal processing) and the pinching beamformer (physical antenna positions) simultaneously. Existing solutions usually rely on "double-loop" alternating optimization, which is computationally expensive, slow to converge, and highly sensitive to initial settings.

Methods

The authors propose an Element-wise Sequential Optimization Framework to break the complexity of joint design.

  1. Hardware Model: The system uses dielectric waveguides where small dielectric particles (Pinching Antennas or PAs) can be positioned. These waveguides allow for near-lossless signal transmission, while the PAs induce emission/reception at specific points.
  2. Downlink & Uplink Design: The paper evaluates standard linear schemes: Maximum Ratio (MRT/MRC), Zero-Forcing (ZF), and Minimum Mean Square Error (MMSE).
  3. The "Aha" Optimization: Instead of optimizing all antenna positions at once, the framework optimizes one PA's position at a time while keeping others fixed.
  4. For the downlink, they derived closed-form expressions that turn the sum-rate maximization into a simple one-dimensional (1D) search for each antenna.
  5. For the uplink, they utilized the Matrix Inversion Lemma (Sherman-Morrison formula) to update the signal-to-interference-plus-noise ratio (SINR) without re-calculating complex matrix inverses at every step.
  6. Eliminating the Loop: This approach allows the baseband beamformer to be updated implicitly as the antennas move, removing the need for the "inner-outer" iteration loops common in prior research.

Datasets

The study relies on numerical simulations rather than empirical datasets. The authors modeled a 28 GHz (millimeter-wave) environment with the following parameters:

  • Service Area: 50m x 6m rectangular region.
  • Hardware: 5 waveguides, each with 6 sliding antennas (PAs), serving 4 users.
  • Channel Model: Line-of-Sight (LoS) dominated, incorporating in-waveguide power loss (attenuation factor $\kappa = 0.1$ dB/m).
  • Benchmark: A hybrid beamforming-based MIMO (hMIMO) system with fixed antennas.

Key Insights and Ideas

  • Pinching Gain vs. Path Loss: PASS excels because it can physically move antennas closer to users, effectively "shortening" the wireless link and reducing large-scale path loss—something fixed antennas simply cannot do.
  • ZF is the "Sweet Spot": In fixed systems, Zero-Forcing (ZF) often struggles at low SNRs. In PASS, however, the antennas can move to positions that avoid "bad" channel states. Consequently, ZF performs nearly as well as the more complex MMSE, making it a highly attractive option for practical PASS implementation.
  • Spatial Flexibility: PASS is far more robust to large service areas. As the area size increases, fixed antennas suffer from increased average distance to users, while PASS antennas simply slide to maintain a strong connection.
  • Complexity Reduction: By reducing the problem to a 1D search per element, the computational overhead is slashed, making real-time antenna repositioning more feasible.

Key Results

  • Massive Throughput Gains: In downlink scenarios with 6 PAs per waveguide, PASS achieved sum-rate improvements of 137% (MMSE), 190% (ZF), and 124% (MRT) compared to conventional fixed-antenna systems.
  • Uplink Performance: Similar trends were seen in the uplink, with gains ranging from 54% to 103%.
  • Convergence: The proposed 1D search method reaches near-optimal performance at a search resolution of $10^5$ points, showing clear saturation where further precision isn't necessary.
  • Interference Management: PASS significantly narrows the "low-SNR region" where MRT/MRC usually outperforms ZF, allowing the system to operate in an interference-limited regime more effectively.

Limitations and Future Work

  • LoS Assumption: The paper assumes a Line-of-Sight dominated environment (common in indoor mmWave). Future work is needed to see how PASS handles rich scattering or Non-Line-of-Sight (NLoS) environments.
  • Hardware Dynamics: The model assumes antennas can be placed with infinite precision. Real-world mechanical constraints, such as the speed of moving the PAs and the power consumption of the "pinching" mechanism, were not the focus of this theoretical framework.
  • Multi-User Scaling: While the framework is low-complexity, scaling to hundreds of users and waveguides would still require further optimization of the sequential update order.

Summary updated

Abstract

The pinching-antenna system (PASS) reconstructs wireless channels through pinching beamforming, i.e., optimizing the activated locations of pinching antennas (PAs) along the waveguide. The aim of this article is to investigate the joint design of baseband beamforming and pinching beamforming. A low-complexity element-wise sequential optimization framework is proposed to address the sum-rate maximization problem in PASS-enabled downlink and uplink channels. i) For the downlink scenario, maximum ratio transmission (MRT), zero-forcing (ZF), and minimum mean square error (MMSE) beamforming schemes are employed as baseband beamformers. For each beamformer, a closed-form expression for the downlink sum-rate is derived as a single-variable function with respect to the pinching beamformer. Based on this, a sequential optimization method is proposed, where the positions of the PAs are updated element-wise using a low-complexity one-dimensional search. ii) For the uplink scenario, signal detection is performed using maximum ratio combining (MRC), ZF, and MMSE combiners. A closed-form sum-rate expression is derived for each linear combiner, and a similar element-wise design is applied to optimize the pinching beamforming. Numerical results are provided to validate the effectiveness of the proposed method and demonstrate that: (i) For all considered linear beamformers, the proposed PASS architecture outperforms conventional fixed-antenna systems in terms of sum-rate performance; (ii) in both downlink and uplink channels, ZF achieves performance close to that of MMSE and significantly outperforms MRT or MRC; and (iii) the proposed element-wise design eliminates the need for alternating updates between the baseband and pinching beamformers, thereby ensuring low computational complexity.
BibTeX
@article{sun2026multiuser,
  author = {Mingjun Sun and Chongjun Ouyang and Shaochuan Wu and Yuanwei Liu},
  title = {{Multiuser Beamforming for Pinching-Antenna Systems: An Element-wise Optimization Framework}},
  journal = {IEEE Trans. Wireless Communications},
  year = {2026},
  doi = {10.1109/twc.2025.3625377},
}
Figure