Modeling and Simulation of Gear Pumps based on Modelica/Mworks®

Liping Chen, Zhao Yan, Fanli Zhou, Jianjun Zhao, Tian XianzhaoLinköping 2011 · DOI

Abstract

In this paper, we present a new method of modeling the hybrid external gear pumps based on Modelica and assess it experimentally. We model the whole working process of an external gear pump. The chamber of the pump is divided into a set of Control Volumes (CVs), whose effective volumes change along with the rotation of the gears. The CVs take in fluid from the inlet port and squeeze fluid out at the outlet port. The whole model of the pump also takes into account flow ripple, pressure distribution, leakages, meshing conditions, etc. Details of each component of the whole pump are provided. From the pressure distribution in space of the gear tooth, we can calculate radial force on shaft, based on which the shaft motion can be simulated.

Introduction

External gear pumps are essential components in industrial fuel and hydraulic systems due to their reliability and mechanical simplicity. However, optimizing these pumps for volumetric efficiency and minimizing noise-inducing pressure peaks remains a significant engineering challenge. Traditional modeling approaches often oscillate between overly simplified analytical models that neglect fluid compressibility and leakages, and computationally expensive Computational Fluid Dynamics (CFD) simulations that are impractical for rapid design iterations. This research introduces a "hybrid" modeling approach using the Modelica language, bridging the gap between computational efficiency and physical fidelity.

Methodology: Dynamic Control Volumes and Leakage Modeling

The proposed model, developed on the MWorks platform, discretizes the pump's internal chambers into a series of dynamic Control Volumes (CVs). As the gears rotate, the volume of these CVs is mathematically determined, simulating the intake of fluid at the inlet and its discharge at the outlet.

Figure 1: Schematic of the external gear pump showing the division into Control Volumes (CVs) and key zones like the meshing and transition zones.

A critical aspect of this model is its comprehensive treatment of internal leakages. It accounts for five distinct leakage paths, including flows through gear tips, the meshing zone, and the clearances between the gears and the pump casing. Furthermore, the model incorporates "velocity-driven" leakage, where the gear rotation actively transports fluid through narrow gaps. The meshing dynamics are also specifically addressed, particularly the "trapped volume" phenomenon that occurs during simultaneous tooth contact, which is mitigated by relief grooves to prevent cavitation.

Force Mapping and Pressure Distribution

A key innovation of this hybrid approach is the detailed mapping of pressure distribution across the gear teeth. Rather than treating internal pressure as a uniform scalar, the model calculates pressure as a spatial distribution. This allows for the derivation of the resultant radial force vector acting on the pump shaft.

Figure 4: Visualization of pressure distribution and the resulting radial force (F) and torque (T) vectors acting on the gear shafts.

By calculating these forces, engineers can predict bearing loads and potential shaft wear patterns. This fluid-mechanical coupling is essential for understanding the dynamic behavior of the pump under varying operational conditions.

Experimental Validation and Results

The Modelica-based simulation was validated against experimental data from established literature (Vacca et al., 2007). The results demonstrated high accuracy in predicting volumetric efficiency and flow rates across a wide range of rotational speeds (500 to 2500 r/min). The model successfully captured high-frequency flow ripples, a common source of vibration in hydraulic systems, showing an average flow rate of approximately 15.1 L/min in the test case.

Conclusion and Future Directions

The hybrid CV-based model provides a robust tool for the rapid design and analysis of external gear pumps. While the current iteration assumes a fixed shaft position and constant fluid temperature, future work will integrate the calculated radial forces to simulate actual shaft motion within oil-film bearings. Additionally, incorporating thermal effects to account for viscosity changes at high pressures will further enhance the model's diagnostic capabilities for real-world applications.

Summary updated

Abstract

In this paper, we present a new method of modeling the hybrid external gear pumps based on Modelica and assess it experimentally. We model the whole working process of an external gear pump. The chamber of the pump is divided into a set of Control Volumes (CVs), whose effective volumes change along with the rotation of the gears. The CVs take in fluid from the inlet port and squeeze fluid out at the outlet port. The whole model of the pump also takes into account flow ripple, pressure distribution, leakages, meshing conditions, etc. Details of each component of the whole pump are provided. From the pressure distribution in space of the gear tooth, we can calculate radial force on shaft, based on which the shaft motion can be simulated.
BibTeX
@inproceedings{chen2011modeling,
  author = {Liping Chen and Zhao Yan and Fanli Zhou and Jianjun Zhao and Tian Xianzhao},
  title = {{Modeling and Simulation of Gear Pumps based on Modelica/Mworks®}},
  booktitle = {Linköping},
  year = {2011},
  doi = {10.3384/ecp11063421},
}
Figure