Mobile Unmanned Aerial Vehicles (UAVs) for Energy-Efficient Internet of Things Communications

Mohammad Mozaffari, Walid Saad, Mehdi Bennis, Mérouane Debbah

Abstract

This paper presents a framework for optimizing the 3D placement and mobility of multiple Unmanned Aerial Vehicles (UAVs) serving as aerial base stations for energy-constrained Internet of Things (IoT) networks. By jointly optimizing device association, power control, and UAV trajectory, the proposed approach achieves a 45% reduction in IoT device transmit power and a 28% improvement in system reliability compared to stationary deployments.

Introduction

The proliferation of the Internet of Things (IoT) involves numerous battery-limited sensors that often struggle to maintain long-range communication with terrestrial base stations. Unmanned Aerial Vehicles (UAVs) offer a flexible solution as "flying base stations." However, their deployment involves complex trade-offs between sensor power consumption, UAV flight energy, and network interference. This research addresses the joint optimization of UAV positioning and mobility to maximize network efficiency.

System Model and Methodology

The system considers a set of IoT devices distributed across a geographical area, served by multiple UAVs. The optimization problem is tackled through a two-step iterative framework.

System model of UAV-assisted IoT communication, illustrating 3D placement, device association, and mobility.

1. Static Snapshot Optimization

At any discrete time interval, the system optimizes UAV placement and device association.

  • Association & Power Control: For fixed UAV locations, an iterative algorithm determines the optimal device-to-UAV mapping and minimizes transmit power to satisfy Signal-to-Interference-plus-Noise Ratio (SINR) requirements.
  • 3D Placement: UAV coordinates are optimized using Sequential Quadratic Programming (SQP) for interference-heavy scenarios or convex optimization for interference-free environments.

2. Dynamic Mobility & Timing

To account for varying device activation patterns, the framework determines optimal "update times" for UAV repositioning.

  • Activation Models: The system uses Periodic and Probabilistic (Beta distribution) models to predict when sensors will be active.
  • Trajectory Planning: The Hungarian Method is employed to solve the 3D trajectory mapping problem, minimizing the energy expended by UAVs during movement between optimal locations.

Results and Discussion

Simulations in a 1 km x 1 km urban environment with 500 IoT devices demonstrate significant performance gains. The mobile UAV approach reduced total IoT transmit power by 45% and improved reliability by 28% over stationary alternatives. In interference-free scenarios, power savings reached up to 80%. Furthermore, the iterative algorithm demonstrated high computational efficiency, converging in fewer than five iterations and operating 500 times faster than brute-force methods with only an 11% optimality gap.

Conclusion

While the framework significantly enhances IoT energy efficiency, future work is needed to address dynamic obstacles, mobile IoT devices, and backhaul link constraints. Additionally, integrating battery replenishment logistics for the UAV fleet remains a critical area for practical deployment.

Summary updated

Abstract

In this paper, the efficient deployment and mobility of multiple unmanned aerial vehicles (UAVs), used as aerial base stations to collect data from ground Internet of Things (IoT) devices, are investigated. In particular, to enable reliable uplink communications for the IoT devices with a minimum total transmit power, a novel framework is proposed for jointly optimizing the 3D placement and the mobility of the UAVs, device-UAV association, and uplink power control. First, given the locations of active IoT devices at each time instant, the optimal UAVs' locations and associations are determined. Next, to dynamically serve the IoT devices in a time-varying network, the optimal mobility patterns of the UAVs are analyzed. To this end, based on the activation process of the IoT devices, the time instances at which the UAVs must update their locations are derived. Moreover, the optimal 3D trajectory of each UAV is obtained in a way that the total energy used for the mobility of the UAVs is minimized while serving the IoT devices. Simulation results show that, using the proposed approach, the total-transmit power of the IoT devices is reduced by 45% compared with a case, in which stationary aerial base stations are deployed. In addition, the proposed approach can yield a maximum of 28% enhanced system reliability compared with the stationary case. The results also reveal an inherent tradeoff between the number of update times, the mobility of the UAVs, and the transmit power of the IoT devices. In essence, a higher number of updates can lead to lower transmit powers for the IoT devices at the cost of an increased mobility for the UAVs.
BibTeX
@article{mozaffari2017mobile,
  author = {Mohammad Mozaffari and Walid Saad and Mehdi Bennis and Mérouane Debbah},
  title = {{Mobile Unmanned Aerial Vehicles (UAVs) for Energy-Efficient Internet of Things Communications}},
  journal = {IEEE Trans. Wireless Communications},
  year = {2017},
  url = {https://openreview.net/forum?id=tCx_acoNnB7},
}

Loading related content...

Figure