Microfluidic channel fabrication by PDMS-interface bonding

Winnie W. Y. Chow, Kin Fong Lei, Guangyi Shi, Wen J. Li, Qiang Huang

TL;DR

This paper introduces a novel, low-temperature method for bonding PMMA microfluidic channels using a thin PDMS interlayer. This technique overcomes limitations of existing methods by preventing substrate deformation and achieving reliable seals, paving the way for more precise and accessible microfluidic device fabrication.

What Problem Does This Paper Address?

Creating functional microfluidic devices often requires bonding multiple substrate layers to form enclosed channels. For polymer-based devices, which are increasingly popular for biological applications due to their low cost and biocompatibility, achieving a strong and precise bond without deforming the delicate microchannels is a significant challenge. Traditional methods like thermal compression, ultrasonics, or gluing can induce global or localized geometric distortions, especially problematic for micron and nanometer-sized channels. Existing polymer-to-polymer bonding methods often require high temperatures that can melt or deform polymer substrates like PMMA (glass transition temperature ~105°C). While PDMS is a popular material for microfluidics due to its low curing temperature, it doesn't readily bond to PMMA using standard oxygen plasma treatments. This paper addresses the need for a low-temperature, precise, and reliable bonding method for PMMA microfluidic channels.

Methods

The core of this paper is a novel PDMS-interface bonding technique. The process begins with creating microchannel patterns on a PMMA substrate using a hot embossing technique. This involves:

  1. Mastering: Creating a nickel mold with the desired channel pattern, typically by electroplating onto an SU-8 patterned silicon wafer.
  2. Replication: Heating a PMMA substrate above its glass transition temperature (~120°C) and compressing the nickel mold onto it under pressure (6.89 MPa) to transfer the channel pattern.

Once the patterned PMMA substrate is prepared, the bonding process proceeds:

  1. PDMS Interlayer Preparation: A thin layer of PDMS prepolymer (10-25 µm) is spin-coated onto a bare PMMA substrate.
  2. Pre-curing: The PDMS-coated substrate is then pre-cured at room temperature for approximately 20 hours. This step increases the PDMS viscosity without fully curing it, making it "sticky" and suitable for bonding.
  3. Bonding: The pre-cured PDMS-coated PMMA substrate is brought into contact with the hot-embossed PMMA substrate.
  4. Final Curing: The assembled stack is then heated at 90°C for 3 hours under pressure (50 kPa). This completes the PDMS curing, forming a strong bond between the two PMMA substrates and sealing the microchannels.

Datasets

Not discussed in the paper. The paper focuses on a fabrication method and its characterization rather than a machine learning approach requiring training datasets.

Key Insights and Ideas

  • PDMS as a Low-Temperature Adhesive: The paper demonstrates that PDMS, when used as a thin interlayer, can effectively bond PMMA substrates at a relatively low temperature (90°C), avoiding the thermal deformation issues associated with direct PMMA bonding.
  • Pre-curing is Crucial: The pre-curing step of the PDMS at room temperature for an extended period (around 20 hours) is critical. It increases the PDMS viscosity, allowing it to conform to the PMMA surface and prevent air entrapment, leading to better bonding quality and reduced bubble formation.
  • Precise Interfacial Layer: The method results in a thin and uniform PDMS interfacial layer (around 50 µm), which is crucial for maintaining the integrity of microchannels, especially at smaller scales.
  • Overcoming PDMS-PMMA Incompatibility: Standard oxygen plasma treatments, effective for bonding PDMS to itself or to glass/silicon, fail to create a strong bond between PDMS and PMMA. This new interlayer approach circumvents this limitation.

Key Results

  • Bonding Strength: Tensile bonding tests yielded a bonding strength of approximately 0.015 MPa.
  • Leakage Test: Injected color dyes into fabricated channels at a flow rate of 0.8 ml/min showed no leakage, confirming the integrity of the seals.
  • Channel Dimensions: Microfluidic channels with dimensions of 300 µm (width) × 100 µm (height) × 1.6 cm (length) were successfully fabricated.
  • Deformation: The bonding process did not induce any global geometric deformation of the PMMA substrates.
  • Bubble Formation: Thinner PDMS layers (10 µm) and sufficient pre-curing time (20 hours) were found to reduce bubble formation and improve bonding quality.

Limitations and Future Work

  • Bonding Strength: While 0.015 MPa is sufficient for many applications, it might be a limitation for high-pressure microfluidic systems. The authors note that the bonding strength is influenced by the PDMS layer thickness and pre-curing time.
  • Channel Edge Deformation: SEM images show that PDMS can be squeezed to the round edges of the hot-embossed channels. While it didn't block the channels in this study, it highlights a potential area for optimization.
  • Future Work: The paper suggests this method is a "low cost, fast, and simple way to fabricate polymer microchannels at relatively low temperatures," implying its broad applicability. Further work could explore optimizing the bonding parameters for even higher strengths or for bonding different polymer combinations. The authors also mention that the pre-curing time could potentially be reduced by increasing the pre-curing temperature.

Summary updated

Abstract

A novel technique for bonding polymer substrates using PDMS-interface bonding is presented in this paper. This novel bonding technique holds promise for achieving precise, well-controlled, low temperature bonding of microfluidic channels. A thin (10–25 µm) poly(dimethylsiloxane) (PDMS) intermediate layer was used to bond two poly(methyl methacrylate) (PMMA) substrates without distorting them. Microchannel patterns were compressed on a PMMA substrate by a hot embossing technique first. Then, PDMS was spin-coated onto another PMMA bare substrate and cured in two stages. In the first stage, it was pre-cured at room temperature for 20 h to increase the viscosity. Subsequently, it was bonded to the hot embossed PMMA substrate. In the second stage, PDMS was completely cured at 90 °C for 3 h and the bonding was successfully achieved at this relatively low temperature. Tensile bonding tests showed that the bonding strength was about 0.015 MPa. Microfluidic channels with dimensions of 300 µm × 1.6 cm × 100 µm were successfully fabricated using this novel bonding method.
BibTeX
@inproceedings{chow2005microfluidic,
  author = {Winnie W. Y. Chow and Kin Fong Lei and Guangyi Shi and Wen J. Li and Qiang Huang},
  title = {{Microfluidic channel fabrication by PDMS-interface bonding}},
  booktitle = {Smart},
  year = {2005},
  doi = {10.1088/0964-1726/15/1/018},
}

Loading related content...

Figure