Abstract
BaTiO3 is typically a strong n-type material with tuneable optoelectronic properties via doping and controlling the synthesis conditions. It has a wide band gap that can only harness the ultraviolet region of the solar spectrum. Despite significant progress, achieving visible-light absorbing BTO with tuneable carrier concentration has been challenging, a crucial requirement for many applications. In this work, a p-type BTO with visible-light absorption is realized via iridium doping. Detailed analysis using advanced spectroscopy tools and computational electronic structure analysis is used to rationalize the n- to p-type transition after Ir doping. Results offered mechanistic insight into the interplay between the dopant site occupancy, the dopant position within the band gap, and the defect chemistry affecting the carrier concentration. A decrease in the Ti3+ donor levels concentration and the mutually correlated oxygen vacancies upon Ir doping is attributed to the p-type behavior. Due to the formation of Ir3+ or Ir4+ in-gap energy levels within the forbidden region, the optical transition can be elicited from or to such levels resulting in visible-light absorption. This newly developed Ir-doped BTO can be a promising p-type perovskite-oxide with imminent applications in solar fuel generation, spintronics and optoelectronics.
Introduction
Barium Titanate ($BaTiO_3$, BTO) is a widely utilized perovskite oxide in electronic components. However, its wide bandgap (~3.2 eV) limits its light absorption to the ultraviolet range, and its inherent n-type nature—driven by oxygen vacancies and $Ti^{3+}$ defects—restricts its use in applications requiring p-type semiconductors, such as photocathodes for solar water splitting. This study demonstrates a strategy to overcome these hurdles through Iridium (Ir) doping.
Experimental and Computational Methods
Samples were synthesized via solid-state reaction at 900 °C. The structural integrity and phase purity were verified using X-ray diffraction (XRD) against ICSD standards. Advanced characterization included Scanning Transmission Electron Microscopy (STEM-HAADF) for atomic-scale imaging and X-ray Photoelectron Spectroscopy (XPS) to probe chemical states. Electronic properties were further investigated using Valence Band XPS (VB-XPS) and photoelectrochemical measurements, complemented by Density Functional Theory (DFT) calculations to model the electronic density of states.
Structural and Chemical Characterization
XRD analysis confirmed that the Ir-doped BTO maintains the cubic perovskite structure of the parent material. A subtle shift in the diffraction peaks toward lower angles suggests lattice expansion, consistent with the successful substitution of larger $Ir^{3+/4+}$ ions into the $Ti^{4+}$ sites.
XPS analysis of the Ir 4f region revealed the coexistence of $Ir^{3+}$ and $Ir^{4+}$ oxidation states. This mixed-valence state is crucial for the observed electronic transitions. Furthermore, doping was found to significantly reduce the concentration of $Ti^{3+}$ and associated oxygen vacancies, effectively suppressing the material's natural n-type bias.
Realizing Visible Light Absorption and p-type Behavior
The incorporation of Iridium introduces new energy levels within the forbidden bandgap of BTO. These "in-gap" states act as stepping stones for electronic excitation, extending the absorption onset from 390 nm into the visible spectrum at approximately 600 nm.
Crucially, the Fermi level ($E_F$) undergoes a dramatic shift. In undoped BTO, $E_F$ is located near the conduction band (~2.2 eV above the valence band edge). Upon Ir-doping, $E_F$ moves significantly closer to the valence band (~0.8 eV), a hallmark of p-type behavior. This transition was functionally confirmed by photoelectrochemical tests, which showed a cathodic photocurrent response characteristic of p-type semiconductors.
Conclusion
By substituting Titanium with Iridium, researchers have successfully transformed $BaTiO_3$ into a visible-light-active, p-type semiconductor. This dual achievement—narrowing the effective bandgap and reversing the majority carrier type—opens new avenues for BTO in optoelectronics and solar fuel production. Future work will focus on optimizing dopant concentrations and evaluating long-term stability in photocatalytic environments.
Summary updated