Abstract
Nanophotonic engineering of light-matter interaction at subwavelength scale allows thermal radiation that is fundamentally different from that of traditional thermal emitters and provides exciting opportunities for various thermal-photonic applications. We propose a new kind of integrated and electrically controlled thermal emitter that exploits layered metamaterials with lithography-free and dielectric/metallic nanolayers. We demonstrate both theoretically and experimentally that the proposed concept can create a strong photonic bandgap in the visible regime and allow small impedance mismatch at the infrared wavelengths, which gives rise to optical features of significantly enhanced emissivity at the broad infrared wavelengths of 1.4-14 μm as well as effectively suppressed emissivity in the visible region. The electrically driven metamaterial devices are optically and thermally stable at temperature up to ~800 K with electro-optical conversion efficiency reaching ~30%. We believe that the proposed high efficiency thermal emitters will pave the way towards integrated infrared light source platforms for various thermal-photonic applications and particularly provide a novel alternative for cost-effective, compact, low glare, and energy-efficient infrared heating.
Introduction
Traditional infrared (IR) heaters, commonly used in industrial processing and domestic heating, typically rely on refractory metals like tungsten or nichrome. These materials suffer from significant limitations: they emit substantial "dazzling glare" in the visible spectrum and often exhibit low spectral efficiency in the specific IR bands required for targeted heating or sensing. While nanophotonic engineering offers a path toward selective emission, most existing solutions require complex and expensive nanofabrication techniques, such as electron-beam lithography, which hinder large-scale deployment.
This research introduces a Layered Metamaterial Thermal Emitter (LTE) that achieves high spectral selectivity through a lithography-free fabrication process. By engineering the material's structure to suppress visible light while maximizing IR output, the researchers have developed a "low-glare" heat source suitable for integrated thermal-photonic platforms.
Design and Methodology
The LTE architecture consists of two stacked one-dimensional (1D) photonic lattices deposited on a Ni₈₀Cr‒₀ thin film. The design utilizes a dual-lattice approach to decouple visible suppression from infrared enhancement:
- Top Lattice (SiO₂/Si): This stack is optimized to create a robust photonic bandgap in the visible regime (0.4–0.8 μm), acting as a mirror to suppress unwanted glare.
- Bottom Lattice (Si/Cr/Si): This section is engineered to minimize the impedance mismatch between the device and free space in the infrared range. By matching the characteristic impedance, the device maximizes its absorptivity and, by Kirchhoff’s law, its emissivity in the target IR bands.
- Active Heating Layer: The underlying Ni₈₀Cr‒₀ film serves as both an optical back-reflector and a Joule heating element, allowing for direct electrical control.
The researchers employed the Transfer Matrix Method (TMM) for numerical optimization of the nanolayer thicknesses. Fabrication was achieved via electron-beam evaporation, a scalable process that avoids the need for complex patterning.
Results and Discussion
The LTE demonstrated exceptional spectral selectivity. Experimental measurements using Fourier-transform infrared spectroscopy (FTIR) confirmed an average emissivity of approximately 0.81 in the broad infrared range (1.4–14 μm), while emissivity in the visible range (0.45–0.75 μm) was suppressed to just 0.07.
Key performance metrics include:
- Efficiency: The device achieved an electro-optical conversion efficiency of ~30% at temperatures exceeding 700 K.
- Thermal Stability: The emitters remained stable up to approximately 800 K, maintaining their optical properties under high-temperature operation.
- Blackbody-like IR Emission: In the target 1.4–14 μm range, the radiation spectra closely approximated an ideal blackbody, providing high-quality infrared heat without the associated visible light waste.
Conclusion and Future Outlook
The proposed LTE offers a cost-effective and efficient alternative for integrated infrared light sources. While the current design is stable up to 800 K, mechanical failure due to thermal expansion mismatch between nanolayers remains a primary limitation for higher-temperature applications. Future research will explore the use of more robust refractory materials, such as hafnium dioxide or aluminum oxide, and thinner substrates to further enhance efficiency and mechanical durability. This work paves the way for compact, energy-efficient, and low-glare infrared heating solutions across industrial and consumer sectors.
Summary updated