Abstract: The onset and kinetics of martensitic transformations are controlled by impurities trapped during the transformation. For the alpha to omega transformation in Ti, ab initio methods yield the changes in both the relative stability of and energy barrier between the phases. Using the recently discovered transformation pathway, we study interstitial O, N, C; substitutional Al and V; and Ti interstitials and vacancies. The resulting microscopic picture explains the observations, specifically the suppression of the transformation in A-70 and Ti-6Al-4V titanium alloys.
Introduction
Titanium's widespread use in aerospace and high-performance engineering stems from its exceptional strength-to-weight ratio. However, its mechanical properties are sensitive to phase transformations. Under high pressure, titanium undergoes a martensitic transformation from the ductile $\alpha$ phase (hexagonal close-packed) to the brittle $\omega$ phase. This transition is undesirable as it compromises toughness and ductility. Interestingly, while high-purity titanium transforms at relatively low pressures (2–9 GPa), commercial alloys like Ti-6Al-4V remain stable up to 35 GPa. This study provides a microscopic explanation for this discrepancy using ab initio simulations.
The Transformation Pathway
The $\alpha \to \omega$ transition is martensitic, meaning it occurs through coordinated atomic movements rather than diffusion. Because it happens near the speed of sound, any impurities present in the lattice are "trapped" in their original positions relative to the surrounding titanium atoms. To model this, the researchers utilized the TAO-1 transformation mechanism, which defines the specific shuffles and strains required for the phase change.
Computational Methodology
The study employed Density Functional Theory (DFT) via the VASP code. The energy barriers of the transformation were calculated using the Nudged Elastic Band (NEB) method with variable cell shapes. Supercells of 48 to 108 atoms were used to simulate impurity concentrations of approximately 1–2 atomic percent, reflecting typical commercial alloy compositions. The investigation covered interstitial impurities (O, N, C), substitutional impurities (Al, V), and intrinsic defects like vacancies and self-interstitials.
Key Insights and Results
The core finding is that impurities significantly increase the energy barrier required for the transformation, effectively "pinning" the material in the $\alpha$ phase.
1. Interstitial Impurities (O, N, C)
Oxygen, Nitrogen, and Carbon were found to act primarily through steric effects. These atoms occupy sites in the $\alpha$ phase that become energetically unfavorable in the $\omega$ phase. As shown in Figure 2(a), the presence of these interstitials nearly doubles the peak energy barrier. Despite their different chemical identities, O, N, and C produce similar barrier increases because their atomic radii are comparable, leading to similar lattice distortions.
2. Substitutional Impurities (Al, V)
The effect of substitutional atoms is governed by electronic factors, specifically the d-electron concentration. Vanadium, a transition metal, actually lowers the energy of the $\omega$ phase relative to $\alpha$. However, Aluminum, a simple metal, strongly stabilizes the $\alpha$ phase. In the common Ti-6Al-4V alloy, the stabilizing effect of Aluminum and Oxygen far outweighs the destabilizing effect of Vanadium, leading to a net barrier increase of approximately 33 meV/atom—nearly four times that of pure titanium (9 meV/atom).
3. The Trapping Mechanism
The "trapping" occurs because the transformation is too rapid for impurities to diffuse to more stable sites. They are forced into high-energy configurations in the $\omega$ phase, creating a massive "drag" on the transformation front. This explains why commercial alloys require much higher pressures to initiate the phase change than high-purity samples.
Conclusion
This research clarifies the long-standing mystery of why commercial titanium alloys are more pressure-resistant than pure Ti. By identifying the specific steric and electronic roles of common impurities, the study provides a framework for understanding phase stability in complex alloys. The results demonstrate that even small concentrations of "trapped" atoms can fundamentally alter the kinetic landscape of martensitic transformations, shifting theoretical phase boundaries and increasing the energy required for structural transitions.
Summary updated