In Situ Synchrotron Microtomography Reveals Multiple Reaction Pathways During Soda‐Lime Glass Synthesis

Emmanuelle Gouillart, Michael J. Toplis, Julien Grynberg, Marie‐Hélène Chopinet, E. Søndergård, L. Salvò, M. Suéry, Marco Di Michiel, Gaël Varoquaux

Abstract

Ultrafast synchrotron microtomography has been used to study in situ and in real time the initial stages of silicate glass melt formation from crystalline granular raw materials. Significant and unexpected rearrangements of grains occur below the nominal eutectic temperature, and several drastically different solid‐state reactions are observed to take place at different types of intergranular contacts. These reactions have a profound influence on the formation and composition of the liquids produced, and control the formation of heterogeneities.

Introduction

Industrial glass production is a massive, energy-intensive process that involves heating a mixture of sand (silica), soda ash (sodium carbonate), and limestone (calcium carbonate) to temperatures exceeding 1500°C. While the final product is ubiquitous, the initial stages of how these discrete grains transform into a homogeneous liquid have long remained a "black box." Traditional "post-mortem" analyses—heating, quenching, and observing 2D slices—fail to capture the dynamic, three-dimensional interplay between grains. Understanding these early stages is crucial, as they dictate the formation of defects like gas bubbles and unmelted grains that can compromise glass quality.

Experimental Methodology

The researchers employed in-situ synchrotron microtomography at the European Synchrotron Radiation Facility (ESRF), specifically the ID15A beamline. Using high-energy white X-ray radiation (40 keV), they achieved a spatial resolution of 1.6 µm. This setup allowed for full 3D scans every 2.6°C as the sample was heated from room temperature to 1100°C.

The mixture consisted of Ronceveaux silica sand (64 wt%), Solvay sodium carbonate (19 wt%), and Saint-Germain calcium carbonate (17 wt%), with grain sizes ranging from 80 µm to 320 µm. Advanced image segmentation enabled the tracking of 175 individual grains (108 sand and 56 calcium carbonate), quantifying volume changes and identifying chemical reaction pathways based on local grain-to-grain contacts.

Key Insights: The "Neighborhood" Effect

The study revealed that the fate of a grain is determined by its microscopic "neighborhood" long before the mixture reaches its nominal melting point.

Solid-State Rearrangements

Sodium carbonate does not remain inert until melting. Below its melting point, it reacts with sand to form a porous shell of crystalline sodium silicates. This reaction causes soda grains to fragment and "crawl," moving toward unreacted portions of sand grains. This unexpected mobility below the eutectic temperature suggests that solid-state reactions drive significant structural changes early in the process.

3D visualization of grain rearrangement and reaction between 770°C and 800°C.

Diverse Reaction Pathways

Different intergranular contacts lead to distinct outcomes:

  • Sand + Soda: Results in rapid reaction and significant volume loss of the sand grains.
  • Lime + Soda: Forms a Na-Ca double carbonate, which eventually melts into a liquid that "cements" the granular structure.
  • Isolated Lime: Limestone grains not in contact with soda simply calcine into refractory $CaO$ grains, which are primary candidates for solid defects in finished glass.

Quantitative Results and Reaction Milestones

The researchers identified specific temperature milestones where the fraction of solid phases significantly decreases.

Quantitative analysis of grain volume changes (a) and reaction milestones as a function of temperature (b).

As shown in Figure 4, approximately one-third of the sand grains experienced a volume decrease starting at 760°C, but only those with sodium carbonate neighbors. Two major drops in the solid phase fraction were observed:

  1. 820°C: Corresponding to the equilibrium eutectic between sodium metasilicate ($NS$) and disilicate ($NS_2$).
  2. 865°C: Marking the melting of the remaining sodium carbonate.

Furthermore, liquid formation was observed at 760°C, which is lower than the lowest stable eutectic temperature (790°C) in the $Na_2O-SiO_2$ system, suggesting the presence of metastable phases that accelerate melting.

Conclusion and Future Outlook

This work demonstrates that the path to a perfect glass melt is dictated by local microscopic interactions. By "watching" the birth of glass in 3D, researchers can now identify the origins of defects and the mechanisms of early-stage melting. While the 1.6 µm resolution is impressive, future work could investigate sub-micron reaction layers or how varying grain size distributions and the addition of recycled glass ("cullet") can optimize these pathways for better energy efficiency and higher glass purity.

Summary updated

Abstract

Ultrafast synchrotron microtomography has been used to study in situ and in real time the initial stages of silicate glass melt formation from crystalline granular raw materials. Significant and unexpected rearrangements of grains occur below the nominal eutectic temperature, and several drastically different solid‐state reactions are observed to take place at different types of intergranular contacts. These reactions have a profound influence on the formation and composition of the liquids produced, and control the formation of heterogeneities.
BibTeX
@article{gouillart2012i,
  author = {Emmanuelle Gouillart and Michael J. Toplis and Julien Grynberg and Marie‐Hélène Chopinet and E. Søndergård and L. Salvò and M. Suéry and Marco Di Michiel and Gaël Varoquaux},
  title = {{<i>In Situ</i> Synchrotron Microtomography Reveals Multiple Reaction Pathways During Soda‐Lime Glass Synthesis}},
  journal = {Journal of the American Ceramic Society},
  year = {2012},
  doi = {10.1111/j.1551-2916.2012.05151.x},
}
Figure