Fabrication of Length Tunable ZnO Nanowire Arrays and Investigation on Their Effect for Dye-Sensitized Solar Cells

Meili WangJournal of Material Science & Engineering 2012 · DOI

Abstract

A series of ZnO nanowire arrays were grown on seeded fluorine-doped tin oxide (FTO) substrates by hydrothermal method. The effect of reaction solution concentration on the length and morphology of ZnO nanowire arrays, as well as cell performance in dye-sensitized solar cell (DSSC) was investigated. It was found that with the increase of growth solution concentration, the ZnO nanowires became longer in length, but with the bottom of nanowires gradually interconnected to each other. The enlarged ZnO nanowire length lead to increased power conversion efficiency and achieved the highest efficiency of 1.54% with nanowire length of 8.6 μm; however, the further increased nanowire length and connected bottoms of nanowires restrained the further efficiency improvement due to the increased electron recombination and reduced surface area.

Introduction

Dye-sensitized solar cells (DSSCs) are a promising third-generation solar technology due to their low cost and ease of manufacture. Traditionally, these cells utilize a porous network of titanium dioxide ($TiO_2$) nanoparticles. However, electron transport in these networks is hindered by frequent trapping at grain boundaries, which slows collection and increases energy loss. One-dimensional (1D) nanostructures, such as zinc oxide (ZnO) nanowires, offer a "highway" for electrons, theoretically allowing for faster transport. The primary challenge is that ZnO nanowires typically possess significantly less surface area than nanoparticle films, leading to lower dye adsorption. This study investigates the physical limits of increasing nanowire length to overcome this surface area deficit.

Experimental Methods

The researchers employed a controllable two-step hydrothermal process to grow ZnO nanowire arrays on fluorine-doped tin oxide (FTO) glass. A 300 nm ZnO seed layer was first deposited via RF magnetron sputtering to ensure vertical, c-axis oriented growth. The substrates were then immersed in an aqueous solution of zinc nitrate and ammonia at 95°C. By varying the growth solution concentration from 10 mM to 100 mM, the nanowire length was tuned from 0.8 µm to 11.3 µm while maintaining consistent wire diameters (80–120 nm).

Figure 1: SEM images (a-e) showing the progression of ZnO nanowire length from 0.8 to 11.3 µm, and (f) the corresponding XRD pattern confirming high-quality wurtzite crystallinity.

Results and Discussion

Morphological characterization revealed that as the nanowires grew longer, their bases began to merge and interconnect. This "crowding" effect reduces the effective surface area available for dye molecules and introduces obstacles for electron transport. Photovoltaic performance was evaluated using standard metrics, including J-V curves and Incident Photon-to-Current Conversion Efficiency (IPCE).

Figure 2: IPCE spectra for the five sample groups, demonstrating that efficiency peaks at a nanowire length of 8.6 µm (sample d) before declining.

The highest power conversion efficiency reached was 1.54% with a nanowire length of 8.6 µm. Performance metrics, including short-circuit current density ($J_{sc}$), increased steadily up to this point but dropped significantly when the length reached 11.3 µm (falling to 1.05%). This decline is explained by a theoretical maximum diffusion length ($l$) calculated at approximately 7.16 µm for these single-crystal wires. In the 11.3 µm samples, electrons generated in the upper regions of the wire are more likely to recombine with the electrolyte before reaching the electrode.

Conclusion

The study identifies a critical "sweet spot" for ZnO nanowire length in DSSCs. Simply increasing length to boost surface area is limited by electron diffusion constraints (~7 µm) and structural crowding at the nanowire base. Future research should focus on hierarchical structures, such as branched nanowires or nanoparticle-decorated wires, to exponentially increase surface area without exceeding the vertical transport limits identified here.

Summary updated

Abstract

A series of ZnO nanowire arrays were grown on seeded fluorine-doped tin oxide (FTO) substrates by hydrothermal method. The effect of reaction solution concentration on the length and morphology of ZnO nanowire arrays, as well as cell performance in dye-sensitized solar cell (DSSC) was investigated. It was found that with the increase of growth solution concentration, the ZnO nanowires became longer in length, but with the bottom of nanowires gradually interconnected to each other. The enlarged ZnO nanowire length lead to increased power conversion efficiency and achieved the highest efficiency of 1.54% with nanowire length of 8.6 μm; however, the further increased nanowire length and connected bottoms of nanowires restrained the further efficiency improvement due to the increased electron recombination and reduced surface area.
BibTeX
@article{wang2012fabrication,
  author = {Meili Wang},
  title = {{Fabrication of Length Tunable ZnO Nanowire Arrays and Investigation on Their Effect for Dye-Sensitized Solar Cells}},
  journal = {Journal of Material Science \& Engineering},
  year = {2012},
  doi = {10.4172/2169-0022.1000101},
}

Loading related content...

Figure