Effects of Ozone concentration and relative humidity on secondary organic aerosol formation from reactions of 1,3-butadiene with ozone

Ailing Ren, Shanshan Wang, Shuo Zhang, Miao Tian, Ruijing Yao, Shuo Li, Xuan Zhang2016 · DOI

Abstract

The formation of secondary organic aerosol (SOA) products from the photo-oxidation of 1,3-butadiene and ozone was investigated in a static smog chamber. This study specifically examined the influence of ozone ($O_3$) concentration and relative humidity (RH) on particle formation dynamics. Results indicate that increasing ozone concentration (from 0 to 50 ppm) significantly increases the proportion of particles larger than 0.7 μm and accelerates the initial ozone decomposition rate, while having a negligible effect on the total number of particles formed. Similarly, increasing relative humidity from 4% to 25% accelerated ozone decomposition and promoted the formation of larger particles without substantially altering the total particle count.

Introduction

1,3-butadiene is a critical industrial chemical used in the production of synthetic rubber and nylon, yet it is also a hazardous volatile organic compound (VOC) and a known carcinogen. In the atmosphere, it undergoes photo-oxidation to form Secondary Organic Aerosols (SOAs). These aerosols are of significant concern due to their roles in reducing visibility, impacting human respiratory health, and influencing global climate patterns. Understanding how environmental variables like ozone concentration and humidity affect the "recipe" for SOA formation is essential for accurate atmospheric modeling and public health assessments.

Experimental Methodology

The researchers conducted experiments using a 0.3 $m^3$ static smog chamber constructed from FEP-Teflon film, chosen for its chemical inertness and UV transparency. The system simulated atmospheric photo-oxidation by exposing the mixture to UV radiation at 400 μW/cm².

Figure 1: Schematic diagram of the experimental setup used to study SOA formation, including the ozone generator, reactor chamber, and analytical instruments.

As shown in the experimental setup (Figure 1), mass flow controllers were used to inject precise amounts of 1,3-butadiene and ozone. Real-time monitoring was performed for ozone levels and humidity, while particle size and count were tracked across three specific bins: 0.3–0.5 μm, 0.5–0.7 μm, and >0.7 μm using a specialized particle counter.

Key Results and Discussion

The Role of Ozone and the "Size Shift"

Ozone was identified as the indispensable trigger for SOA formation; in control experiments with 0 ppm $O_3$, no particle formation was observed. A primary finding of this study is that while ozone concentration does not significantly change the total quantity of particles produced, it fundamentally alters their size distribution.

Figure 4: Time-series data showing the number of particles larger than 0.7 μm at varying initial ozone concentrations. Higher ozone levels lead to a greater abundance of large-diameter particles.

As illustrated in Figure 4, higher initial ozone concentrations (e.g., 50 ppm) led to a dramatic increase in the number of particles in the >0.7 μm size range compared to lower concentrations. This suggests that higher ozone levels promote the rapid growth or aggregation of smaller initial nuclei into larger aerosol fractions. Most of this dynamic growth occurs within the first 10 minutes of the reaction, coinciding with the period of most rapid ozone decay.

Influence of Relative Humidity

Relative humidity (RH) acted as a catalyst for these processes. Increasing RH from 4% to 25% resulted in a faster initial ozone decomposition rate. Similar to the ozone concentration effect, higher humidity favored the formation of larger particles (>0.7 μm) but did not significantly impact the total steady-state particle count. This indicates that moisture facilitates the chemical pathways leading to larger molecular weight products or enhances the physical growth of existing particles.

Conclusion and Future Directions

This study demonstrates that environmental factors like ozone and humidity primarily dictate the physical characteristics (size) of SOAs formed from 1,3-butadiene rather than the absolute number of particles. Future research should expand the humidity range to reflect tropical conditions (>80% RH) and utilize mass spectrometry to characterize the specific chemical species within these aerosols. Additionally, exploring complex mixtures of VOCs and nitrogen oxides ($NO_x$) would provide a more comprehensive understanding of real-world urban smog dynamics.

Summary updated

Abstract

The formation of secondary organic aerosol products from photo-oxidation of 1,3butadiene and ozone was investigated in static smog chamber. The effects of ozone concentration and relative humidity on the particle formation were studied. Research suggests that with the increase of ozone concentration (0-50 ppm), the particle size of particles larger than 0.7 m accounted for the proportion of the total number of particles increased and the initial stage of the ozone decomposition rate increased. But the increase in ozone concentration has little effect on the total number of particles. Relative humidity of 4% and 25% of the experimental data show that in the relative humidity of 25%, the initial stage of the ozone decomposition rate is faster and particle size larger than 0.7 m accounted for a larger proportion of the total number of particles. In the same way, the change in relative humidity has little effect on the total number of particles.
BibTeX
@misc{ren2016effects,
  author = {Ailing Ren and Shanshan Wang and Shuo Zhang and Miao Tian and Ruijing Yao and Shuo Li and Xuan Zhang},
  title = {{Effects of Ozone concentration and relative humidity on secondary organic aerosol formation from reactions of 1,3-butadiene with ozone}},
  year = {2016},
  doi = {10.2991/emcpe-16.2016.43},
}
Figure