Effect of TiC Content on the Microstructure and Mechanical Properties of TiC/Fe Matrix Composites Fabricated by Spark Plasma Sintering

Chuan Wang, Yong Li, Wanpeng Zhang, Tianwen Zhao, Huiqiao DuJournal of the Japan Society of Powder and Powder Metallurgy 2025 · DOI

This study, published in the Journal of the Japan Society of Powder and Powder Metallurgy, explores the delicate balance between reinforcement and structural integrity in metal matrix composites. Researchers from Beihang University investigated how varying the amount of Titanium Carbide (TiC) affects iron-based composites fabricated via Spark Plasma Sintering (SPS).

TL;DR

Adding more hard ceramic reinforcement to a metal matrix doesn't always result in a stronger material; in this study, increasing TiC content from 25% to 41% actually triggered a "porosity trap" that weakened the composite. The 25 wt% TiC sample emerged as the top performer, balancing low porosity (3.85%) with high hardness (595 HV0.5) and superior bending strength (662 MPa).

What Problem Does This Paper Address?

Particle-reinforced metal matrix composites (P-MMCs) are the workhorses of the automotive and petrochemical industries, prized for their hardness and wear resistance. Titanium Carbide (TiC) is a go-to reinforcement because it is thermally stable, cost-effective, and generally "wets" well with iron-based matrices.

However, there is a limit to how much ceramic you can pack into a metal matrix before the material's properties begin to degrade. Traditional powder metallurgy often struggles with long sintering times that lead to coarse, brittle microstructures. While Spark Plasma Sintering (SPS) offers a faster, more controlled alternative, researchers still lack a comprehensive understanding of how high TiC loading affects the final porosity and fracture mechanics of these specific iron-matrix composites.

Methods

The researchers prepared a complex composite powder consisting of an iron-based alloy (Fe-Cr-Mo-Co-Al-Ni) mixed with three different weight percentages of TiC: 25%, 33%, and 41%.

  1. Preparation: The powders were mixed using high-energy ball milling to ensure a uniform distribution.
  2. Sintering: The team used Spark Plasma Sintering (SPS). Unlike traditional furnace sintering, SPS uses pulsed direct current and high pressure (54 MPa) to heat the material rapidly (100°C/min) to 1120°C. This "flash" sintering helps prevent excessive grain growth.
  3. Analysis: The team used Scanning Electron Microscopy (SEM) to look at the "topography" of the fractures, X-ray Diffraction (XRD) to identify new chemical phases formed during sintering, and universal testing machines to measure mechanical limits.

Datasets

As an experimental materials science paper, this study does not use external digital datasets. Instead, it generates primary experimental data across three sample groups (25%, 33%, and 41% TiC). The results are benchmarked against empirical formulas for hardness (Salak’s linear model) and flexure strength (Pomahoba’s non-linear model).

Key Insights and Ideas

  • The Porosity Trap: The most significant finding was that higher TiC content led to higher porosity. At 41% TiC, the particles tend to "agglomerate" (clump together). During sintering, the metal matrix cannot easily flow into the tiny gaps between these clumps, leaving behind microscopic voids.
  • Chemical "Aha" Moments: Sintering isn't just a physical process; it's a chemical one. XRD analysis revealed the formation of novel phases like (Ti, Mo)C and $Al_2Mo_3C$. These occur because atoms from the matrix (like Molybdenum and Aluminum) substitute into or react with the TiC structure, creating new, ultra-hard compounds that help anchor the reinforcement to the matrix.
  • Fracture Evolution: The way the material breaks tells a story.
  • At 25% TiC, the bond is so strong that cracks go through the grains (transgranular fracture).
  • At 41% TiC, the high porosity and clumping cause the material to fail between the grains (intergranular fracture), resulting in a "block sugar" appearance under the microscope.

Key Results

  • Optimal Loading: The 25 wt% TiC composite was the clear winner, exhibiting the lowest porosity (3.85%), the highest Vickers hardness (595 HV0.5), and the highest bending strength (662 MPa).
  • The Decline: As TiC increased to 41%, porosity jumped to 6.86%, while bending strength plummeted to 530 MPa.
  • Mathematical Correlation: The researchers confirmed that hardness decreases linearly as porosity increases. However, bending strength follows a non-linear exponential decay, meaning even small increases in porosity can disproportionately weaken the material's resistance to snapping.

Limitations and Future Work

The study is limited to a specific range of high TiC content (25–41%). It does not explore whether a "sweet spot" exists below 25% or how different sintering temperatures might mitigate the porosity seen at 41%.

Future research could investigate surface treatments for TiC particles to improve their "wettability," potentially allowing for higher ceramic loading without the penalty of increased porosity. Additionally, testing the wear resistance and corrosion resistance of these specific alloy-modified matrices would provide a more complete picture for industrial applications.

Summary updated

Abstract

The titanium carbide particles reinforced iron matrix composites (TiC/Fe MCs) with different TiC contents of 25, 33, and 41 wt% were fabricated using spark plasma sintering (SPS). The effect of TiC content on the microstructure and mechanical properties of the TiC/Fe MCs was studied. The results were obtained from scanning electron microscopy (SEM), Vickers hardness testing, and universal testing machine. The porosity increases with an increase in TiC content. At TiC content of 25%, the composite exhibits minimum porosity of 3.85% and demonstrates excellent overall properties, including Vickers hardness value of 595 HV0.5 and bending strength of 662 MPa. This enhancement in performance can be attributed to the improved anchoring effect provided by carbon related phases at relatively low levels of porosity. Furthermore, analysis of fracture mechanisms reveals that when the TiC content is below 33%, transgranular fracture and ductile fracture are dominant; however, intergranular fracture becomes predominant when the TiC content exceeds 41%.
BibTeX
@article{wang2025effect,
  author = {Chuan Wang and Yong Li and Wanpeng Zhang and Tianwen Zhao and Huiqiao Du},
  title = {{Effect of TiC Content on the Microstructure and Mechanical Properties of TiC/Fe Matrix Composites Fabricated by Spark Plasma Sintering}},
  journal = {Journal of the Japan Society of Powder and Powder Metallurgy},
  year = {2025},
  doi = {10.2497/jjspm.17f-t15-08},
}
Figure