TL;DR
This paper investigates how drawing bicomponent PBT/PET fibers with a unique four-lobed cross-section induces crimping, a key feature for high-performance textiles. They developed a novel model combining existing theories with a viscoelastic framework to accurately predict this draw-induced crimping and found that these profiled fibers also exhibit improved wettability.
What Problem Does This Paper Address?
Self-crimping fibers are highly desirable for textiles due to their enhanced elasticity, bulk, and dimensional stability. While thermal methods for inducing crimp in bicomponent fibers are well-studied, the mechanisms behind mechanically induced crimping, specifically through drawing, remain less understood. This gap is particularly relevant for designing advanced functional fibers. Furthermore, the impact of fiber cross-sectional geometry on both crimping and functional properties like wettability needs further exploration. This research aims to elucidate the draw-induced crimping mechanism in a novel four-lobed PBT/PET fiber and assess its wettability compared to circular fibers.
Methods
The researchers produced four-lobed side-by-side PBT/PET bicomponent fibers using a custom melt-spinning process. These fibers were then subjected to drawing at 80°C with varying draw ratios (from 1.6 to 4.0).
Key experimental techniques included:
- Fiber Fineness Measurement: Using a skein method.
- Cross-Sectional Morphology (SEM): To visualize the four-lobed structure.
- Tensile Mechanical Property Tests: Measuring tenacity, elongation at break, and initial modulus.
- Fiber Tension Measurement: In-line measurement of draw tension.
- Creep Behavior Tests: On single-component PET and PBT fibers to characterize their viscoelastic properties.
- Crimp Radius Measurement: Using optical microscopy to quantify crimp geometry.
- Static Contact Angle Measurement: To assess fiber wettability.
The core theoretical contribution is a novel predictive model for crimp curvature. This model integrates:
- Denton's Crimp Theory: A classical model for bicomponent fiber crimp.
- Four-Element Viscoelastic Model: To capture the time-dependent deformation behavior of PET and PBT under stress, crucial for understanding draw-induced effects.
This model was further refined with an empirical correction factor to reconcile theoretical predictions with experimental results.
Datasets
Not discussed in the paper. The study relies on experimental data generated from the manufactured fibers and literature data for shrinkage properties.
Key Insights and Ideas
- Drawing as a Crimp Driver: Mechanical drawing, not just thermal treatment, is a powerful tool for inducing significant helical crimp in bicomponent fibers. This opens up new avenues for fiber design and processing.
- Viscoelasticity is Key: The time-dependent deformation (viscoelasticity) of PET and PBT under drawing is the fundamental driver of differential shrinkage, leading to crimp. The four-element model effectively captures this.
- Four-Lobed Geometry Matters: The unique four-lobed cross-section not only influences the crimp morphology but also enhances the fiber's wettability.
- PBT's Higher Shrinkage: Due to its higher intrinsic viscosity and resulting greater chain entanglement, PBT exhibits higher shrinkage than PET, causing it to occupy the inner side of the crimped structure.
- Model Predicts Reality: The developed model, incorporating Denton's theory and viscoelasticity, accurately predicts the draw-induced crimp radius, especially after an empirical correction.
Key Results
- Enhanced Strength: Increasing the draw ratio from 1.6 to 4.0 significantly improved fiber tenacity from 0.64 cN/dtex to 3.91 cN/dtex.
- Reduced Crimp Radius: As the draw ratio increased, the crimp radius decreased from 2.05 mm to 0.64 mm, indicating tighter crimps.
- Improved Wettability: Four-lobed fibers showed a lower static contact angle (71.28°) compared to circular fibers (74.84°), a reduction of approximately 3.56°.
- Model Accuracy: The corrected predictive model achieved a high coefficient of determination (R²) of 0.9951, demonstrating excellent agreement with experimental crimp radius data.
- Mechanical Property Trade-offs: While drawing significantly increased strength and stiffness, it led to a substantial decrease in elongation at break.
Limitations and Future Work
The authors acknowledge several limitations:
- Literature Shrinkage Data: The model relied on literature values for boiling water shrinkage, which may differ from the actual thermal conditions (80°C hot rolls) experienced during drawing.
- Coupling of Shrinkages: The model simplifies the complex interplay between draw-induced and thermal shrinkage, treating them as additive. In reality, these processes are coupled and can influence each other.
- Single-Fiber Focus: Wettability was assessed at the single-fiber level. Future work should extend this to fabric-level studies to evaluate moisture management properties like wicking and drying.
Future work suggested includes:
- Directly measuring AS under hot-roll conditions.
- Conducting DMA tests to refine viscoelastic parameters across a temperature range.
- Developing more sophisticated coupled models to account for the interaction between draw-induced and thermal shrinkage.
- Performing sensitivity analyses to understand how parameter uncertainties affect predictions.
- Extending wettability evaluation to fabric-scale experiments.
Summary updated