Abstract
The IEEE 1451 standard family provides a framework for smart transducer interfaces, enabling "Plug and Play" (PnP) functionality between sensors and processors. While IEEE 1451.4 is commonly used for single sensors, it is often inadequate for complex multi-sensor arrays. This paper details the design and implementation of an "electronic tongue" system—a multi-array chemical sensor—using the IEEE 1451.2 standard. By utilizing Transducer Electronic Data Sheets (TEDS) and a standardized Transducer Independent Interface (TII), the researchers developed a modular, intelligent sensing platform capable of automated identification and high-precision liquid analysis.
Introduction
Electronic tongues are sophisticated analytical tools that utilize arrays of non-specific chemical sensors to identify complex liquid samples. A significant challenge in their development is the lack of a standardized interface, which often necessitates manual hardware configuration and calibration. While the IEEE 1451.4 standard addresses smart sensors, it lacks the structural capacity to efficiently describe the relationships within a multi-sensor array. This research applies the IEEE 1451.2 standard to bridge this gap, creating a unified architecture for array-based chemical sensing.
System Architecture
The core of the proposed system is the interaction between a Network Capable Application Processor (NCAP) and a Smart Transducer Interface Module (STIM). The STIM acts as the intelligent bridge between the raw chemical sensors and the digital network.
As illustrated in the architectural overview, the STIM integrates interface logic, signal conditioning, and the Transducer Electronic Data Sheets (TEDS) required for self-identification. This modularity allows the electronic tongue to be treated as a single intelligent unit that can be swapped or updated without reconfiguring the entire network.
Implementation and Interface Design
The researchers implemented a Multi-Array Chemical Sensor (MACS) consisting of seven ion-selective electrodes (targeting ions such as $H^+$, $K^+$, and $Ca^{2+}$) and one reference electrode. To manage this array, a PIC18F8720 microcontroller was used within the STIM to handle data acquisition and communication.
Transducer Independent Interface (TII)
A critical component of the IEEE 1451.2 standard is the Transducer Independent Interface (TII). This 10-line digital bus facilitates standardized communication between the STIM and the NCAP.
The TII includes lines for data clocking (DCLK), data input/output (DIN/DOUT), and control signals like NACK (acknowledge) and NINT (interrupt). This standardized physical layer ensures that any NCAP—whether a PC, PDA, or industrial controller—can communicate with the electronic tongue if it adheres to the protocol.
Transducer Electronic Data Sheets (TEDS)
The system's "intelligence" is derived from TEDS stored in a 32KB EEPROM. The implementation included:
- Meta-TEDS: Describing the overall multi-sensor system configuration.
- Channel-TEDS: Storing specific calibration constants and attributes for each of the eight sensor channels.
- Meta-Identification TEDS: Containing manufacturer and model information.
By storing calibration data directly on the sensor module, the system achieves true PnP functionality. When connected, the NCAP automatically reads the TEDS and configures itself to interpret the sensor signals correctly.
Results and Discussion
The experimental results confirmed the feasibility of the IEEE 1451.2 architecture for complex chemical sensing. The system achieved high-resolution data acquisition using a 16-bit ADC, providing a resolution of approximately $102 \mu V$ per LSB. Signal integrity was maintained through high-input-impedance buffers and low-pass filters designed to handle the high impedance characteristic of chemical sensors.
Key findings included:
- Efficiency: A complex 8-channel system was fully described using only 945 bytes of TEDS data.
- Interoperability: The software successfully identified the sensor array and its specific attributes via the TII without manual user input.
- Analytical Capability: Principal Component Analysis (PCA) performed on the acquired data demonstrated that the standardized system could effectively distinguish between different liquid samples.
Conclusion
Applying IEEE 1451.2 to electronic tongue design significantly simplifies the integration of multi-sensor arrays into broader networks. By standardizing the interface and embedding calibration data within the sensor module itself, the researchers have moved closer to a "plug and play" paradigm for chemical analysis. Future work will focus on integrating these smart modules into wireless ubiquitous sensor networks (USN) and addressing the long-term stability of the chemical sensors themselves.
Summary updated