Design and Preparation of New Type Day and Night Filter

Maojin Dong, Tao Chen, Yuqing Xiong, Duoshu Wang, Jizhou Wang2012 · DOI

Abstract

In order to image no color cast in daytime, and form black and white image at night, we use day and night filter to instead mechanical switching system in infrared night vision camera and monitoring system. Essential Macleod software is used to optimize the film spectra, the average transmittance exceeds 90% in 440~640nm. The spectra has a band pass in 850nm, the bandwidth is less than 40nm, and the peak transmittance is less than 20%. Physics vapour depositing method with the aid of ion beam assistant deposition systems is adopted. Through reducing film thickness error and optimizing technical parameter, we get the new type day and night filters on substrate of K9 glass.

Introduction

Modern surveillance cameras utilize CCD or CMOS sensors sensitive to both visible and infrared (IR) light. While beneficial for night vision, this dual sensitivity causes a "color cast" during the day, as the sensor detects IR light invisible to the human eye, leading to distorted color reproduction. Traditionally, cameras employ a mechanical "IR-cut" filter that physically moves in front of the sensor during the day. However, these mechanical systems are prone to failure and increase device bulk. This research presents an "unbalanced" dual-channel optical filter that eliminates the need for mechanical switching by precisely controlling IR transmission.

Design Strategy and Optimization

The core innovation lies in the "unbalanced" spectral design. Unlike traditional dual-band filters that allow high IR transmission, this new design restricts the 850nm IR channel to a peak transmittance of less than 20% with a narrow bandwidth (<40nm). This provides sufficient light for night imaging without overwhelming the visible color balance during the day.

To achieve this non-intuitive structure, the researchers moved away from symmetric periodic structures. They employed the needle optical method integrated with genetic algorithms and the simplex method via Essential Macleod software. This computational approach allowed the design to "tunnel" through local minima to find an optimal multilayer configuration that meets stringent spectral requirements.

Comparison of spectral designs for traditional (dashed) and new-type (solid) filters.

Fabrication via Ion Beam Assisted Deposition

The filters consist of multilayer dielectric films—specifically high-purity titanium oxide ($Ti_2O_3$) and silica ($SiO_2$)—deposited on K9 glass substrates. Fabrication was carried out using Ion Beam Assisted Deposition (IBAD) within a physical vapor deposition system.

The use of a cold cathode ion source was critical. By providing additional energy to evaporating particles and supplementing oxygen atoms in the titanium oxide layers, IBAD ensures the creation of a dense, stable, and highly adherent film. This process is essential for maintaining the durability and spectral integrity of the filter in various environmental conditions.

Experimental Results

The performance of the fabricated filters was verified using a Lambda 900 spectrophotometer. The experimental results closely matched the theoretical design specifications:

  • Visible Band (440–640nm): Average transmittance exceeded 90%, ensuring bright and accurate color imaging during the day.
  • Infrared Band (850nm): Peak transmittance was successfully limited to <20% with a bandwidth of <40nm.
  • Blocking Regions: Transmittance was kept below 3% in the 665–790nm and 900–1100nm ranges, effectively minimizing noise.
Measured transmittance spectrum of the fabricated new-type filter showing high visible transmission and a controlled IR peak.

The resulting filter effectively eliminates daytime color cast while allowing for clear black-and-white imaging at night, successfully replacing mechanical switching systems in infrared night vision cameras.

Conclusion and Future Outlook

While the "unbalanced" filter design proves effective, the primary challenge for mass production is the presence of systematic errors in the coating process. These errors can lead to spectral variations between production batches. Future research will focus on sensitivity analysis to identify critical layers most affected by thickness errors and on refining process controls to improve reproducibility and yield.

Summary updated

Abstract

In order to image no color cast in daytime, and form black and white image at night, we use day and night filter to instead mechanical switching system in infrared night vision camera and monitoring system. Essential Macleod software is used to optimize the film spectra, the average transmittance exceeds 90% in 440~640nm. The spectra has a band pass in 850nm, the bandwidth is less than 40nm, and the peak transmittance is less than 20%. Physics vapour depositing method with the aid of ion beam assistant deposition systems is adopted. Through reducing film thickness error and optimizing technical parameter, we get the new type day and night filters on substrate of K9 glass.
BibTeX
@misc{dong2012design,
  author = {Maojin Dong and Tao Chen and Yuqing Xiong and Duoshu Wang and Jizhou Wang},
  title = {{Design and Preparation of New Type Day and Night Filter}},
  year = {2012},
  doi = {10.2991/emeit.2012.285},
}
Figure