Abstract
Applications of rolling diaphragm transmissions for medical and teleoperated robotics are of great interest, due to the low friction of rolling diaphragms combined with the power density and stiffness of hydraulic transmissions. However, the stiffness-enabling pressure preloads can form a tradeoff against bearing loading in some rolling diaphragm layouts, and transmission setup can be difficult. Utilization of cable drives compliment the rolling diaphragm transmission's advantages, but maintaining cable tension is crucial for optimal and consistent performance. In this paper, a coaxial opposed rolling diaphragm layout with cable drive and an electronic transmission control system are investigated, with a focus on system reliability and scalability. Mechanical features are proposed which enable force balancing, decoupling of transmission pressure from bearing loads, and maintenance of cable tension. Key considerations and procedures for automation of transmission setup, phasing, and operation are also presented. We also present an analysis of system stiffness to identify key compliance contributors, and conduct experiments to validate prototype design performance.
Introduction
In specialized robotic applications such as MRI-compatible surgical tools and wearable exoskeletons, remote actuation is often a necessity. Moving power from a remote motor to a distal joint requires a transmission that is both high-torque and "transparent"—meaning it has minimal friction and backlash. While standard hydraulic systems offer high power density, their sliding O-ring seals introduce significant friction. Rolling diaphragms (RD) offer a low-friction alternative by replacing sliding seals with a rolling flexible membrane. However, RDs typically require high internal pressures to maintain stiffness, which can lead to excessive bearing loads and complex setup procedures.
Mechanical Design and Methodology
To address these challenges, researchers at UCSD developed a novel transmission unit featuring a coaxial opposed rolling diaphragm layout. This design utilizes a "Translating Core" where two diaphragms face each other. By balancing internal fluid pressure within this central core, the high preload pressures required for stiffness are decoupled from the mechanical bearings, preventing premature wear and friction.
To convert the linear motion of the core into rotation, the system employs a helical cable drive. By wrapping cables around a capstan with a symmetrical "fleet angle," the design cancels out moment loads on the shaft. This symmetry is critical for eliminating the "tilting" forces that often plague similar actuators, ensuring smoother motion. Furthermore, because the cables are fixed within the rigid core, tension is maintained even when the hydraulic lines are depressurized, enhancing clinical reliability.
Automated Transmission Control
A significant hurdle in hydrostatic transmissions is "phasing" — the precise alignment of the input motor and the output joint. Manual calibration is often tedious and prone to error. This system introduces an electronic transmission control system that automates setup and phasing.
Using a "Predictive Phasing" algorithm, a microcontroller manages solenoid valves and a water pump to add or remove precise amounts of fluid. This allows the system to align input and output shafts to within 0.4° accuracy automatically. The control system also manages "Hibernation" and "Setup" modes, transforming the complex hydraulic assembly into a user-friendly, "plug-and-play" component.
Performance Analysis and Results
The team conducted a comprehensive stiffness analysis to identify primary sources of compliance. Experimental results revealed that the rolling diaphragm itself is the most significant contributor to system "squishiness," accounting for 46.1% of total compliance. Additionally, even minute amounts of undissolved air (as low as 0.01%) were found to drastically reduce system stiffness.
Despite these factors, the prototype demonstrated exceptional transparency:
- High Transparency: The system showed extremely low static friction (0.45%) and hysteresis (1.25%) relative to the full 6Nm torque range.
- Accurate Modeling: Experimental stiffness (18.71 Nm/rad) closely matched theoretical predictions, confirming the system behaves as a predictable second-order spring.
Conclusion and Future Work
The coaxial opposed rolling diaphragm design successfully decouples pressure preloads from bearing loads while providing a high-transparency robotic transmission. While the automated phasing system significantly improves usability, future work will focus on minimizing hose compliance and improving air management to reach theoretical stiffness limits. Further research into diaphragm materials and geometries is also planned to optimize the dynamic "feel" of the actuator for sensitive teleoperation tasks.
Summary updated