Design and Implementation of Real Time Locating System for Efficient Vehicle Pooling in Port Terminal

Sanghyun Son, Hyun-Tae Cho, Yun-Ju BeakThe Journal of the Korean Institute of Information and Communication Engineering 2012 · DOI

Abstract

In a port terminal, containers are stored and transshipped by yard tractors and crane vehicles. For operation efficiency of the terminal, location information of these vehicles is an essential factor. However, most port terminals estimate the location of these assets using indirect methods such as event tracking, which are infrequent and prone to significant errors. This paper proposes a real-time asset tracking system to obtain accurate and reliable location data. The system overcomes estimation errors caused by container stacks that interrupt wireless communication by using custom hardware and an enhanced multi-step locating system. Evaluation at the Hyundai Pusan New Port Terminal (HPNT) demonstrated an accuracy of approximately 5.87 meters (CEP).

Introduction

Efficient logistics in modern port terminals depend heavily on "vehicle pooling"—the dynamic dispatching of Yard Tractors (YT) to cranes. To optimize this process, precise real-time location data is required. Traditional "event-based" tracking (e.g., recording a location only when a container is moved) is insufficient due to low update frequency and high cumulative error. Furthermore, satellite-based GPS often fails in the "urban canyons" created by towering metal container stacks, which block line-of-sight (LOS) signals and cause severe Non-Line-of-Sight (NLOS) errors.

System Architecture and Methodology

The proposed Real-Time Locating System (RTLS) is designed to operate in radio-hostile environments using three core components:

  1. Custom Hardware: Specialized tags for YTs and readers for infrastructure use Chirp Spread Spectrum (CSS) at 2.4GHz (IEEE 802.15.4a). CSS provides superior resistance to the interference and multipath fading common in industrial settings.
  2. Multi-Step Locating Protocol: The system utilizes a "Blink and Range" approach. Tags periodically broadcast their presence ("Blink"), followed by Symmetric Double-Sided Two-Way Ranging (SDS-TWR) to measure the time-of-flight between tags and readers. SDS-TWR is particularly effective as it eliminates the need for complex clock synchronization between devices.
  3. Mobile Anchors: To address coverage gaps between fixed readers on high light poles, "mobile readers" are mounted on Quay Cranes (QC) and Transfer Cranes (TC). These cranes act as moving reference points, maintaining clear LOS to tractors operating directly beneath them.
System architecture overview showing fixed and mobile readers in a port terminal environment.

Location Estimation Engine

The software backend processes raw distance data through a three-stage pipeline:

  • Pre-filter: Removes outliers and compensates for hardware-specific sensor errors.
  • Estimator: Employs trilateration via least squares estimation. It integrates data from both fixed and mobile readers. A critical feature is the inclusion of magnetometers on mobile readers to account for crane orientation, preventing errors when cranes operate in reverse.
  • Post-filter: Smoothes the final position using the vehicle's trajectory and physical speed constraints.
Mathematical formulation for the trilateration-based location estimation engine.

Experimental Results

The system was deployed and evaluated at the Hyundai Pusan New Port Terminal (HPNT) in South Korea, utilizing 66 fixed readers and 85 tractor tags. Performance was measured at 30 specific test points where tractors frequently operate.

The system achieved an average location accuracy of 5.87 meters (Circular Error Probable - CEP), with a maximum recorded error of 9.76 meters and a standard deviation of 2.76 meters. This represents a significant improvement over previous state-of-the-art systems in similar environments, which typically average around 10 meters of error. Trajectory mapping confirmed that the filtering algorithms successfully maintain logical vehicle paths even during temporary signal dropouts in deep shadow areas.

Conclusion

The proposed RTLS provides a robust solution for the unique challenges of port terminal logistics. By combining CSS-based hardware, mobile crane-mounted anchors, and a sophisticated multi-step estimation engine, the system achieves the precision necessary for efficient vehicle pooling. Future enhancements may include the integration of Inertial Measurement Units (IMU) to provide dead reckoning during complete signal blockages and exploring Ultra-Wideband (UWB) technology for even higher precision.

Summary updated

Abstract

항만 터미널 내에서 컨테이너의 이동을 위해 야드 트랙터와 크레인 차량을 이용한다. 차량의 빠른 배치를 통한 효율적인 처리를 위해 차량의 위치정보가 중요한 요소로 떠오르고 있다. 현재 대부분의 항만 터미널에서 차량의 위치 정보는 해당 차량이 마지막으로 발생시킨 이벤트를 기반으로 하여 추정하나 차량이 발생시키는 이벤트는 발생 빈도가 낮으며 추정하는 위치 오차가 크게 발생하는 문제가 있다. 본 논문에서는 이러한 문제를 극복하기 위해 차량의 위치를 측정하기 위한 무선 통신 기반 실시간 위치 측정 시스템을 제안한다. 항만 터미널 환경은 컨테이너의 적재로 위치 측정 오차가 크게 발생한다. 이를 해결하기 위해 항만환경에 적합한 하드웨어를 설계 및 구현하고 항만 터미널의 추가적인 문제를 해결한 향상된 다단계 위치 측정 기법을 적용하여 위치 정보의 정확도를 향상시켰다. 제안하는 시스템을 현대 부산 신항만 터미널(HPNT)에서 측정 정밀도를 테스트한 결과 CEP 기준으로 평균 5.87 미터 오차수준의 정확도를 확인하였다. In a port terminal, containers are stored and transshipped by yard tractors and crane vehicles. For operation efficiency of the terminal, location information of these vehicles is an essential factor. However, most of port terminals try to estimate location of these assets using indirect methods such as event tracking of shipping or unshipping containers. Because these kinds of events are rarely occurred, location of the event includes seriously locating error compared to a real location of vehicle. In this paper, we propose a real-time asset tracking system to obtain accurate and reliable location of terminal assets. The proposed system overcomes a location estimation error caused by container stacks which interrupt wireless communication. In order to mitigate uncertainty and increase accuracy of location estimation, we designed hardwares and multi-step locating system to resolve additional preblems. We implemented system components, and installed these at a port environment for evaluation. The result shows superiority of the system that the accuracy is approximately 5.87 meters (CEP).
BibTeX
@article{son2012design,
  author = {Sanghyun Son and Hyun-Tae Cho and Yun-Ju Beak},
  title = {{Design and Implementation of Real Time Locating System for Efficient Vehicle Pooling in Port Terminal}},
  journal = {The Journal of the Korean Institute of Information and Communication Engineering},
  year = {2012},
  doi = {10.6109/jkiice.2012.16.9.2056},
}
Figure