Cross-layer design for reducing delay and maximizing lifetime in industrial wireless sensor networks

Jiawei Tan, Anfeng Liu, Ming Zhao, Hailan Shen, Ming Ma

Abstract

Industrial Wireless Sensor Networks (IWSNs) are essential for monitoring critical infrastructure, requiring both low latency for real-time reporting and long operational lifetimes due to the difficulty of battery replacement. This paper presents the RDML (Reducing Delay and Maximizing Lifetime) scheme, which optimizes performance across the physical, MAC, and network layers. By employing non-equidistant node deployment and strategically utilizing residual energy in peripheral nodes to reduce retransmissions, the RDML scheme demonstrates a 19–30% reduction in network delay and a 43% increase in network lifetime compared to traditional uniform deployment models.

Introduction

In industrial environments, IWSNs serve as the primary data acquisition layer for monitoring complex systems. These networks must satisfy two often-conflicting objectives: minimizing transmission delay for time-sensitive events and maximizing the network's operational lifespan. A significant challenge in multi-hop IWSNs is the "Energy Hole" problem, where nodes closer to the data sink deplete their batteries faster as they relay traffic from the entire network. While previous research often addresses these layers in isolation, this study proposes a cross-layer design to balance these trade-offs effectively.

The RDML Scheme

The proposed RDML scheme integrates optimizations across the Physical, MAC, and Network layers to address the energy hole problem and latency issues simultaneously.

Non-Equidistant Deployment

A core component of the RDML scheme is the move away from uniform node spacing. The authors developed an algorithm for non-equidistant deployment, where nodes are placed at specific, unequal distances to balance the energy load. This ensures that nodes near the sink and those at the network edge deplete their energy at approximately the same rate, maximizing the overall network lifetime.

Fig. 1: Illustration of the linear network deployment model used in the RDML scheme.

Strategic Residual Energy Utilization

The scheme identifies that peripheral nodes typically possess "surplus" energy because they handle less relay traffic. RDML increases the duty cycles of these nodes. Although this increases local energy consumption, it significantly enhances transmission reliability and reduces the latency associated with MAC-layer retransmissions.

Experimental Setup

The RDML scheme was validated through rigorous mathematical modeling and extensive numerical simulations. The study considered both linear and grid topologies, accounting for variables such as path loss, bit error rates (BER), and circuit power consumption.

Table 1: Key simulation parameters and values used to validate the RDML model.

The simulation parameters, detailed in Table 1, reflect typical industrial conditions, including a path loss exponent of 3 and a transmission period of 100 ms.

Results and Discussion

The RDML scheme was benchmarked against "Equal Distance" and "Optimal Duty Cycle" models. Key findings include:

  • Delay Reduction: Network latency was reduced by 19–30%, primarily due to improved reliability in the peripheral nodes.
  • Lifetime Extension: The network's operational life increased by more than 43% through balanced energy depletion.
  • Energy Efficiency: The total network energy utilization rate saw significant improvements, with simulation data closely aligning with theoretical proofs.

Conclusion

The RDML scheme demonstrates that treating node deployment and energy management as a unified cross-layer problem yields superior results for industrial applications. By strategically "wasting" energy in non-bottleneck nodes, the system achieves lower latency without sacrificing longevity. Future research will explore the integration of these optimizations with Cloud and Fog computing architectures and their performance in highly dynamic or irregular industrial topologies.

Summary updated

Abstract

Low delay and long lifetime are a very important issue for industrial wireless sensor networks (IWSNs) in which it require long-time monitoring of industrial sites and respond quickly to events that is monitored; therefore, high delay communications can cause serious damage to property and personnel at industrial field. Due to delay, lifetime, and other performance involved to multiple layers, it is difficult to optimize from a single layer. Therefore, a cross-layer design optimal scheme for reducing delay and maximizing lifetime (RDML) scheme is proposed for IWSNs which is from several layers such as transmitted power, duty cycle, and node deployment positions to optimize the network performance of delay and lifetime etc. Firstly, due to the node which sends a packet within a cycle, different duty cycle leads to different selection of the modulation level, resulting in different power consumption efficiency of transmitting data. Through careful analysis, the optimal value of the duty cycle is given which has the lowest energy consumption per bit. In fact, the energy consumption of the node is not balanced. Therefore, an optimization method of changing the duty cycle is proposed. In this paper, larger duty cycle is chosen for nodes with residual energy to improve the reliability of data transmission, reducing the probability of data retransmission, so that the network delay can be reduced in IWSNs. Third, based on the previous analysis, a network optimization deployment algorithm is proposed, which not only maximizes the energy efficiency of a single node but also maximizes the network lifetime and the total network energy efficiency. Both our comprehensive theoretical analysis results indicate that the performance of RDML scheme is better than the previous studies. Relative to equal distance and optimal duty cycle scheme, the RDML scheme can reduce the delay by 19–30% and increase the lifetime by more than 43%.
BibTeX
@article{tan2018cross,
  author = {Jiawei Tan and Anfeng Liu and Ming Zhao and Hailan Shen and Ming Ma},
  title = {{Cross-layer design for reducing delay and maximizing lifetime in industrial wireless sensor networks}},
  journal = {EURASIP J. Wirel. Commun. Netw.},
  year = {2018},
  doi = {10.1186/s13638-018-1057-x},
}
Figure