Consideration of Thermal Expansion Compensation for Giant Magnetostrictive Actuator

Yoshikazu Tatsumi, Kazuyuki Ohtake, Ryuhei Takahashi, Hirosi Eda, Kohji Tashiro, Hiroyuki Wakiwaka, Hisashi Yajima, Naoki FujiwaraJournal of the Magnetics Society of Japan 2009 · DOI

Abstract

Giant magnetostrictive material (GMM) is fabricated by electromechanical transformation with large magnetostriction and an electro-mechanical coupling factor. Therefore, GMM can be used to make a giant magnetostrictive actuator (GMA). However, because the thermal expansion (linear expansion) coefficient of GMM is approximately 12 ppm/°C, expansion and contraction due to temperature changes significantly influence the actuator's stroke. This paper describes the consideration of thermal expansion compensation for the GMA, presenting the features of GMM, the results of thermal expansion measurements, and a novel thermal expansion compensation method using a tandem structure.

Introduction: The Challenge of Thermal Drift

Giant Magnetostrictive Materials (GMM), typically alloys like Terfenol-D, are essential for high-precision engineering due to their ability to change shape under magnetic fields, offering high force and rapid response. However, these materials face a significant challenge: heat. Internal copper coils in an actuator generate Joule heating during operation. With a thermal expansion coefficient of 12 ppm/°C, the GMM rod expands independently of magnetic control. This "thermal drift" can severely compromise precision; for instance, a 20°C temperature rise can cause an unwanted expansion of 6.7 µm in a device intended for a 28 µm stroke.

Design of the Tandem Magnetostrictive Actuator (T-GMA)

To address this, a Tandem Magnetostrictive Actuator (T-GMA) was developed. Unlike standard GMAs that use a single GMM rod, the T-GMA utilizes two rods linked by a specialized "tandem connector."

Internal structure of the proposed Tandem Giant Magnetostrictive Actuator (T-GMA).

The design incorporates a coil, permanent magnets for biasing, and a yoke to complete the magnetic circuit. The key innovation lies in the mechanical arrangement of the GMM rods and the connector material.

Principles of Thermal Compensation

The core strategy for compensation involves material matching and geometric inversion. Aluminum was selected for the tandem connector due to its thermal expansion coefficient (~23.4 ppm/°C), which is nearly double that of GMM (~12 ppm/°C).

Schematic representation of the thermal expansion compensation principle using a tandem connector.

As shown in the principle diagram, the GMM rods expand in one direction when heated (ΔT > 0). The tandem connector is designed to expand in the opposite direction. By sizing the aluminum connector to be approximately half the total length of the GMM assembly, its greater expansion rate theoretically cancels out the GMM's expansion, maintaining a stable "Base level" for the actuator's output.

Experimental Results

The performance of the T-GMA was compared against a standard GMA using high-precision optical micrometers (0.1 µm accuracy) and thermocouples.

  • Standard GMA: Exhibited a thermal expansion coefficient of 15.7 ppm/°C.
  • Tandem GMA (T-GMA): Successfully reduced the effective expansion to 5.5 ppm/°C.
  • Efficiency: The tandem structure achieved a 65% reduction in thermal drift compared to conventional designs.

While the results confirm the effectiveness of the tandem design, the compensation was not 100%. This is attributed to a temperature distribution imbalance: the GMM rods, being closer to the heat-generating coils, reach higher steady-state temperatures faster than the aluminum connector.

Conclusion and Future Outlook

The tandem structure provides a robust, passive solution for mitigating thermal drift in high-power actuators without the need for complex active cooling. Future improvements will focus on optimizing the heat path to the tandem connector to ensure it reaches thermal equilibrium simultaneously with the GMM rods. Equalizing the temperature distribution across the assembly could further close the remaining 35% gap in compensation, enabling even higher levels of precision in thermally volatile environments.

Summary updated

Abstract

Giant magnetostrictive material (GMM) is fabricated by electromechanical transformation with large magnetostriction and an electro-mechanical coupling factor. Therefore, GMM can be use to make a giant magnetostrictive actuator. However, because the thermal expansion (linear expansion) coefficient of GMM is 12 ppm/°C, expansion and contraction due to temperature change influences the stroke. This paper describes the consideration of thermal expansion compensation for the GMA, and presents: (1) the features of GMM and the principles of operation of GMA, (2) the results of thermal expansion measurements of GMA, and (3) thermal expansion compensation for the tandem structure.
BibTeX
@article{tatsumi2009consideration,
  author = {Yoshikazu Tatsumi and Kazuyuki Ohtake and Ryuhei Takahashi and Hirosi EDA and Kohji Tashiro and Hiroyuki Wakiwaka and Hisashi Yajima and Naoki Fujiwara},
  title = {{Consideration of Thermal Expansion Compensation for Giant Magnetostrictive Actuator}},
  journal = {Journal of the Magnetics Society of Japan},
  year = {2009},
  doi = {10.3379/msjmag.0907rg0004},
}
Figure