Abstract
The giant magnetostrictive actuator has great use in vibration control, but the linear model cannot fully describe its dynamic characteristics. In this chapter, based on the domain wall theory and piezomagnetic theory, a hysteresis nonlinear model is established to fully describe the actuator dynamic characteristics. In combination with the regularisation method, a sliding mode controller has been designed, and the giant magnetostrictive actuator is also studied in the application of active control. Experimental results show that the hysteresis nonlinear model proposed in the chapter can fully describe the actuator's dynamic characteristics in a wider frequency band and the active control also has a much better isolation effect than the passive vibration; it can significantly attenuate the external incentives.
Introduction
Vibration isolation is a cornerstone of precision engineering, essential for applications ranging from aerospace systems to micro-manufacturing. While traditional passive isolation methods—utilizing springs and dampers—are effective in many scenarios, they often struggle to mitigate low-frequency "micro-vibrations." Active control systems employing smart materials, such as Giant Magnetostrictive Actuators (GMAs), offer a promising alternative due to their high precision and rapid response times.
However, the implementation of GMAs is complicated by significant hysteresis nonlinearity, where the actuator's output depends on the history of previous inputs rather than just the current state. Most existing research relies on simplified linear models that are only valid at low frequencies. This paper presents a high-fidelity nonlinear model for GMAs that accounts for hysteresis and wide-frequency dynamics, paired with a robust sliding mode controller to achieve superior vibration suppression.
Modeling and Methodology
The researchers developed a comprehensive modeling framework to capture the complex behavior of the GMA. Unlike standard linear approximations, this model is rooted in domain wall theory and piezomagnetic theory, specifically utilizing the Jiles-Atherton model. This approach captures the intricate coupling between magnetization, mechanical stress, and physical strain.
The model incorporates critical factors for wide-band performance, including magnetization change rates, eddy current losses, and stress changes ($\partial M / \partial \sigma$). By treating magnetization as a function of both the magnetic field and physical stress, the model accurately predicts behaviors that linear models typically overlook. To manage the remaining nonlinearities and external disturbances, a sliding mode controller (SMC) was designed. SMC is particularly valued for its robustness; once the system state reaches a predefined "sliding surface," it remains largely immune to parameter variations and external noise.
Experimental Validation
The proposed framework was validated using a custom-built double-layer vibration isolation test rig. The setup included the GMA, laser displacement sensors, and a JZK-40 shaker to simulate real-world external disturbances. Data acquisition was handled via an NI host controller and LabVIEW software. The experiments utilized a variety of excitation signals, including single-frequency, multi-frequency, and random signals to test the system's versatility.
Key Insights and Results
A primary finding of the study is the "butterfly" effect observed in GMA output. Without an appropriate bias magnetic field, the actuator's response is highly nonlinear and shaped like a butterfly. The authors demonstrated that optimizing the preload (set to 6.7 MPa) and the bias magnetic field (14 kA/m) could significantly linearize the actuator's baseline behavior.
The active control system demonstrated a dramatic reduction in vibration displacement compared to passive isolation:
- Single Frequency Excitation: 81.08% reduction.
- Multi-Frequency Excitation: 78.21% to 81.13% reduction.
- Random Excitation: 55.34% reduction.
Quantitatively, at a primary resonance frequency of 2.8 Hz, the Root Mean Square (RMS) displacement was reduced from 32.1970 µm under passive control to just 6.0899 µm with the active SMC system. Unlike passive systems with fixed resonance peaks, the active system effectively "changes the system mode" to eliminate these peaks, preventing structural instability at specific frequencies.
Conclusion and Future Work
The study successfully demonstrates that a nonlinear hysteresis model combined with sliding mode control can significantly outperform passive vibration isolation across a broad frequency spectrum. However, some limitations remain. Active control performance is relatively less effective at frequencies below 2 Hz, and the isolation effect diminishes once the frequency exceeds the controller's designed effective bandwidth. Future research may focus on adaptive sliding mode controllers capable of real-time tuning to further extend the effective frequency range and enhance performance in the ultra-low frequency domain.
Summary updated