Comparative Analysis of Estimation Formula of Acid Dew Point for Different Flue Gas

Jinhui Song, Li Jia-hu, Hui Yuan, Ren Zhong-qiang2017 · DOI

Abstract

Acid dew point is a critical parameter in boiler design and operation, directly impacting flue gas temperature, boiler efficiency, coal consumption, and waste heat utilization. This study evaluates common acid dew point estimation formulas based on sulfur content, $SO_3$ concentration, and water vapor content across ten typical coal varieties. Results indicate that while most formulas correlate with these parameters, the И.A. Bapahoba (Vapahova) and Japan Electric Power Industry Center models provide the highest accuracy relative to the A.G. Okkes benchmark. Conversely, the Former Soviet Union empirical formula tends to underestimate the dew point, potentially increasing corrosion risks.

Introduction: The Efficiency-Corrosion Dilemma

In coal-fired power plants, the combustion process generates sulfur oxides ($SO_2$ and $SO_3$) and water vapor. When flue gas temperatures drop below the acid dew point, these components condense into sulfuric acid ($H_2SO_4$), causing severe corrosion on boiler tail surfaces. Engineers face a delicate balance: maintaining high exhaust temperatures prevents corrosion but reduces thermal efficiency (a 15–20°C increase costs ~1% efficiency). Conversely, lowering temperatures improves efficiency but risks rapid equipment degradation.

Methodology and Data

To identify the most reliable predictive models, this study compared several international formulas:

  • Empirical Models: Former Soviet Union, Japan Electric Power Industry Center.
  • Semi-Theoretical Models: Muller curve, A.G. Okkes, Verhoff & Branchero, Halstead, and Haase & Borgmann.

These were tested against a dataset of ten Chinese coal varieties, including Lignite, Anthracite, Bituminous, and Lean coal. The testing parameters spanned 0.2% to 1.3% sulfur content, 3 to 12.9 ppm $SO_3$, and 6% to 15.1% water vapor.

Comparative Analysis of Results

The Role of Sulfur and $SO_3$

The analysis confirms that sulfur content and $SO_3$ concentration are primary drivers of the acid dew point. However, the relationship is non-linear and varies significantly across different mathematical models.

Figure 1: Acid dew point temperature vs. Sulfur content (%)

As shown in the figure above, different models yield widely varying estimates for the same sulfur content. The Former Soviet Union model consistently provides the lowest estimates, while the Halstead and Muller curves tend toward the higher end.

Figure 2: Acid dew point temperature vs. SO3 concentration (ppm)

The sensitivity to $SO_3$ concentration is particularly acute at lower levels (below 8.5 ppm). Beyond this threshold, the dew point continues to rise, but the rate of increase diminishes, as illustrated in the comparative plot of the various formulas.

Model Performance Benchmarking

The A.G. Okkes formula is widely regarded as the gold standard due to its high precision (error < 1.5°C). When compared to this benchmark:

  • Best Performers: The И.A. Bapahoba (Vapahova) and Japan Electric Power Industry Center formulas showed the minimal deviation.
  • Underestimation Risk: The Former Soviet Union formula, though popular, consistently under-predicted the dew point. This is likely due to its inclusion of a fly ash absorption factor, which may not be universally applicable or safe for all coal types.
  • High Error Models: The Halstead and Haase & Borgmann formulas exhibited significant errors, reaching up to 20% in some cases, making them less suitable for precise engineering applications.

Conclusion

Accurate estimation of the acid dew point is essential for optimizing boiler performance. While the Former Soviet Union formula is a common industry standard, this study suggests that the Vapahova and Japan Electric Power Industry Center models offer more reliable predictions across diverse coal types. Future research should further investigate the complex interactions between fly ash and acid condensation to refine these predictive tools.

Summary updated

Abstract

Acid dew point is one of the important parameters in boiler design and operation.Its height is closely related to the flue gas temperature, boiler efficiency, coal consumption and the utilization of flue gas waste heat at the tail of the boiler.In this paper, from the point of view of the sulfur content of coal, the concentration of SO3 and the content of water vapor after burning, the common acid dew point estimation formula is used to estimate the corresponding acid dew point value, and the results are analyzed.The results show that the acid dew point and sulfur content coal, coal combustion and SO3 concentrations of water vapor basic related, compared with the A.G.Okkes formula, .A.Bapahoba formula for estimation of the error is small, the former Soviet Union of the empirical formula of acid dew point value is low.
BibTeX
@misc{song2017comparative,
  author = {Jinhui Song and LI Jia-hu and Hui Yuan and Ren Zhong-qiang},
  title = {{Comparative Analysis of Estimation Formula of Acid Dew Point for Different Flue Gas}},
  year = {2017},
  doi = {10.2991/gcmce-17.2017.73},
}
Figure