Camshaft Drive Torque Measuring Device Built in a Chain Sprockt

Masao Ishihama, Sotaro Kanai, Tomohiko IidaInternational Journal of Automotive Engineering 2012 · DOI

Abstract

A device built in a camshaft drive chain sprocket for detecting precise torque fluctuation with minimum change on the valve drive system dynamical characteristics was developed. Strain gages are placed on thin plate areas in the sprocket disc. The signal from the circuit goes through frequency modulation and is transmitted to demodulation circuit via coil antennas. By this arrangement, almost perfect linearity was observed in the relationship of the output voltage and the applied torque. Torque fluctuation measured with this device on a model cylinder head driven by a variable speed motor showed good correlation with simulation results.

Introduction

In the pursuit of higher fuel efficiency and improved engine performance, the optimization of the valve drive system is paramount. This system is a significant contributor to internal combustion engine noise, vibration, and parasitic friction. To refine these components, engineers require precise data on the torque fluctuations transferred between the timing chain and the camshaft.

However, measuring this torque in situ presents a significant engineering challenge. Traditional torque meters are typically bulky or introduce excessive mechanical compliance. Such modifications alter the system's natural frequency and dynamical characteristics—specifically its mass and torsional stiffness—thereby skewing the very data they are intended to collect. Furthermore, sensors must isolate the desired torque signal from "cross-talk" caused by axial thrust and lateral chain tension forces. This paper presents a "smart" camshaft sprocket designed to function as a high-precision torque sensor with minimal impact on the engine's mechanical properties.

Mechanical Design and FEA Optimization

The core innovation lies in the transformation of a standard timing chain sprocket into a measurement transducer. The researchers modified a standard sprocket by machining four "thin webs" arranged in a cross pattern within the sprocket disc. These webs are designed to act as pure shear stress fields.

3D model of the modified sprocket showing thin webs and slits for torque measurement.

To ensure that the tangential force (torque) is channeled exclusively through these measurement zones, narrow slits were cut to decouple the central hub from the peripheral rim. This geometry forces the mechanical load through the thin webs where strain gages are mounted. The design was refined using Finite Element Analysis (FEA) to optimize corner radii, rib thickness, and slit distribution. This optimization ensured a uniform strain distribution across the webs, maximizing the signal-to-noise ratio while maintaining the structural integrity required for engine operation.

Signal Acquisition and Isolation

To avoid the reliability issues and friction associated with physical slip rings, the system utilizes wireless electronics. A custom circuit board is mounted directly onto the rotating sprocket. Power is supplied via a stationary induction coil, and the strain gage signals are converted to a D.C. voltage. This voltage is then frequency-modulated (FM) onto a high-frequency carrier wave and transmitted via a second coil antenna to a stationary stator coil.

A critical aspect of the sensor's accuracy is its ability to isolate torque from other mechanical loads. The arrangement of the strain gages allows for the cancellation of signals resulting from axial thrust or chain tension.

Strain gage configurations for isolating torque from thrust and chain tension.

As shown in the figure, by summing the signals from specific gage pairs (shear and normal strain), the device can mathematically isolate pure torque while rejecting interference from bending or lateral forces. This ensures that the output voltage represents the true torsional load on the camshaft.

Experimental Validation and Results

The device was validated using a 2.0-liter in-line four-cylinder engine head driven by a variable-speed motor. Static calibration demonstrated exceptional linearity, with the relationship between applied torque and output voltage following a near-perfect linear regression.

In dynamic testing at 1500 rpm, the sensor captured torque waveforms that were compared against Multi-Body Dynamics (MBD) simulations performed in AVL Tycon software. The measured waveforms showed excellent agreement with the simulation in the low-frequency range, confirming the sensor's accuracy. Notably, the sensor was sensitive enough to detect the 21st-order variation—a high-frequency ripple caused by the engagement of individual chain links. This level of granularity is often lost in conventional measurement setups and highlights the sensor's superior resolution.

Discussion and Future Work

While the sensor provides high-fidelity data, discrepancies were noted in the high-frequency range when compared to MBD simulations. The authors attribute this to the inherent difficulty in simulating complex factors like oil film viscosity and the stiffness of contact points during valve-cam collisions. This discrepancy highlights the value of the physical sensor in providing "ground truth" data to refine virtual models.

Future work may focus on the long-term durability of the thin-webbed sprocket under the extreme thermal and vibrational stresses of a firing engine. Currently, the technology serves as a vital tool for engine designers looking to reduce parasitic friction and develop more efficient variable valve actuation (VVA) systems.

Summary updated

Abstract

A device built in a camshaft drive chain sprocket for detecting precise torque fluctuation with minimum change on the valve drive system dynamical characteristics was developed. Strain gages are placed on thin plate areas in the sprocket disc. The signal from the circuit goes through frequency modulation and is transmitted to demodulation circuit via coil antennas. By this arrangement, almost perfect linearity was observed in the relationship of the output voltage and the applied torque. Torque fluctuation measured with this device on a model cylinder head driven by a variable speed motor showed good correlation with simulation results. .
BibTeX
@article{ishihama2012camshaft,
  author = {Masao Ishihama and Sotaro Kanai and Tomohiko Iida},
  title = {{Camshaft Drive Torque Measuring Device Built in a Chain Sprockt}},
  journal = {International Journal of Automotive Engineering},
  year = {2012},
  doi = {10.20485/jsaeijae.3.4\_107},
}
Figure