Biobased diblock copolymers and associated reactivity ratios via RAFT-polymerisation as new dispersing additives

Lea Viktoria Rubbert, Philipp Knospe, Sebastian Weiß, Maximilian Scherübl, Lukas Wander, Jochen S. Gutmann, Michael DornbuschRSC 2025 · DOI

Abstract

Diblock copolymers with structural heterogeneity, made of monomers based on renewable resources, were investigated as dispersing additives for nonpolar coating systems. Reversible addition-fragmentation transfer (RAFT) polymerisation was used to obtain (diblock co)polymers with tailor-made structures and molecular weights $M_w$. For this purpose, methacrylates derived from oleyl alcohol and eugenol were utilized. The reaction kinetics of controlled and free radical polymerisation processes for methacrylated eugenol (4-allyl-2-methoxyphenyl methacrylate) (1) and methacrylated oleyl alcohol (octadec-9-en-1-yl methacrylate) (2) were investigated. In addition, commercially available methacrylates—including methyl methacrylate (3), methacrylic acid (4), benzyl methacrylate (5), and stearyl methacrylate (6)—were used for building diblock copolymers. Reaction kinetics of the homopolymers 3 and 6 were compared to those of methacrylates 1 and 2. By RAFT-polymerisation of methacrylate 1, pronounced cross-linking was observed, suggesting the active participation of the allyl group. Subsequent investigations confirmed that the allyl group underwent partial conversion. By lowering the concentration, the cross-linking reaction could be minimized, enabling the synthesis of diblock copolymers. Finally, their performance as dispersing additives was evaluated in non-polar coating systems containing inorganic and carbon black pigments. All diblock copolymers showed good dispersity properties for all pigments, with particularly pronounced effects for the fully bio-based block copolymer poly(2-b-4) and the partially bio-based block copolymer poly(6-b-1).

Introduction: The Challenge of Sustainable Pigment Stabilization

The coatings and paint industry is currently undergoing a significant transition from fossil-based raw materials to renewable, biobased alternatives. However, sustainability must be matched by performance. One of the most critical challenges in paint formulation is pigment stabilization. Pigments naturally tend to reagglomerate, leading to poor color strength, settling, and undesirable high viscosity.

To combat this, dispersing additives—specifically diblock copolymers—are employed. These polymers feature a "tail" compatible with the solvent for steric stabilization and a "head" or anchor group that adheres to the pigment surface. Synthesizing these precise architectures from complex biobased molecules like eugenol is traditionally difficult due to chemical structures that often trigger uncontrolled side reactions.

Methodology: From Bio-Resources to Tailor-Made Polymers

Researchers utilized Reversible Addition-Fragmentation Transfer (RAFT) polymerization to construct these additives. Unlike standard free-radical polymerization, RAFT allows for "brick-by-brick" polymer construction, ensuring narrow molecular weight distributions and precise block structures.

The process began with Monomer Synthesis, converting eugenol (from clove oil) and oleyl alcohol (from rapeseed oil) into methacrylates (Monomers 1 and 2) via Steglich esterification. These were then compared against industrial standards such as methyl methacrylate (3) and stearyl methacrylate (6).

Synthesis of biobased monomers (1 and 2) from eugenol and oleyl alcohol, alongside standard methacrylates (3-6) utilized in the study.

The team employed a "one-pot" method for Diblock Synthesis, where the first block (the "tail") is grown to near-completion before the second monomer (the "anchor") is added to extend the chain. This ensures the formation of well-defined block copolymers.

Reaction scheme for the RAFT polymerization of methyl methacrylate (3) and subsequent chain extension with stearyl methacrylate (6) to form a diblock copolymer.

Key Insights: Managing Reactivity and Cross-linking

A major hurdle identified was the "Allyl Trap" associated with Monomer 1 (methacrylated eugenol). While the allyl group in eugenol is typically non-reactive under these conditions, the study found it caused significant cross-linking during RAFT, leading to branched or gelled polymers. The researchers discovered that by significantly lowering the monomer concentration, they could suppress this intermolecular cross-linking enough to maintain control and produce soluble diblock copolymers.

Additionally, poly-2 (oleyl-based) showed unexpectedly low dispersity even in uncontrolled free-radical polymerization, which the authors attribute to a "self-stabilizing" effect from its long aliphatic chains.

Results: Performance in Coating Systems

The synthesized polymers demonstrated excellent industrial potential:

  • High Conversion & Control: Most polymerizations reached >95% conversion with targeted molecular weights (5,000–7,500 g/mol). RAFT provided excellent control ($M_w/M_n$ as low as 1.1–1.3), though eugenol-containing blocks were slightly higher (~1.8) due to residual allyl activity.
  • Superior Dispersity: The fully biobased copolymer poly(2-b-4) and the partially biobased poly(6-b-1) showed exceptional stabilization. In inorganic pigment formulations, these additives reduced viscosity from 127 mPa·s (control) to a range of 31–60 mPa·s, maintaining stability even after accelerated heat-aging.
  • Thermal Robustness: All polymers were stable up to approximately 170°C, meeting the requirements for industrial coating applications.

Conclusion and Future Directions

While the study successfully managed eugenol cross-linking through dilution, future work could explore more selective catalysts or RAFT agents. Furthermore, to enhance the "circular economy" aspect, the authors suggest moving from food-competing oils (like rapeseed) to recycled cooking oils or microbial fermentation products. Tailoring the "anchor" block further may also improve performance for more challenging organic pigment systems.

Summary updated

Abstract

Diblock copolymers with structural heterogeneity, made of monomers based on renewable resources were investigated as dispersing additives for nonpolar coating systems. Reversible addition-fragmentation transfer (RAFT) polymerisation was used to obtain (diblock co)polymers with tailor-made structures and molecular weights <i>M</i> <sub>w</sub>. For this purpose methacrylates derived from oleyl alcohol and eugenol, were utilized. The reaction kinetics of controlled and free radical polymerisation processes for methacrylated eugenol (4-allyl-2-methoxyphenyl methacrylate) (1) and methacrylated oleyl alcohol (octadec-9-en-1-yl methacrylate) (2) were investigated. In addition, commercially available methacrylates - including methyl methacrylate (3), methacrylic acid (4), benzyl methacrylate (5) and stearyl methacrylate (6) were used for building diblock copolymers. Reaction kinetics of the homopolymers 3 and 6 were compared to those of methacrylates 1 and 2. By RAFT-Polymerisation of Methacrylate 1, pronounced cross-linking was observed, suggesting the active participation of the allyl group. Subsequent investigations confirmed that the allyl group underwent partial conversion. By lowering the concentration, the cross-linking reaction could be minimized, enabling the synthesis of diblock copolymers. Finally, their performance as dispersing additives was evaluated in non-polar coating systems containing inorganic and carbon black pigments. To measure performance, properties such as rheological behavior and particle size distribution were analysed. All diblock copolymers showed good dispersity properties for all pigments, with particularly pronounced effects for the fully bio-based block copolymer poly(2-<i>b</i>-4) and the partially bio-based block copolymer poly(6-<i>b</i>-1).
BibTeX
@inproceedings{rubbert2025biobased,
  author = {Lea Viktoria Rubbert and Philipp Knospe and Sebastian Weiß and Maximilian Scherübl and Lukas Wander and Jochen S. Gutmann and Michael Dornbusch},
  title = {{Biobased diblock copolymers and associated reactivity ratios <i>via</i> RAFT-polymerisation as new dispersing additives}},
  booktitle = {RSC},
  year = {2025},
  doi = {10.1039/d5ra06866e},
}
Figure