AutoCharge: Autonomous Charging for Perpetual Quadrotor Missions

Alessandro Saviolo, Jeffrey Mao, Roshan Balu T. M. B, Vivek Radhakrishnan, Giuseppe Loianno

Abstract

The limited battery endurance of small-scale quadrotors remains a primary bottleneck for long-term autonomous operations. While existing solutions such as battery swapping or wireless charging offer potential remedies, they often introduce significant complexity, weight, or efficiency losses. This paper presents AutoCharge, a novel autonomous charging system designed to enable perpetual missions through a combination of a portable ground station and a flexible, magnetic charging tether. By utilizing an active electromagnet to facilitate docking and orientation-agnostic circular connectors for power transfer, AutoCharge achieves high-efficiency contact charging while remaining robust to the localization and control errors inherent in real-world flight conditions.

Introduction

Modern quadrotors are increasingly deployed for persistent surveillance, infrastructure inspection, and search-and-rescue operations. However, the "Achilles' heel" of these platforms is their limited flight time, typically restricted to 20–30 minutes. To maintain a continuous presence, drones must frequently return to a power source.

Current approaches to autonomous recharging face significant trade-offs. Battery swapping systems are mechanically complex and lack portability. Wireless (inductive) charging is easier to implement but suffers from low efficiency—often 25–30% lower than wired alternatives—and requires high-precision landing. Traditional contact charging offers high efficiency but demands millimeter-level landing accuracy, which is difficult to achieve in windy conditions or with standard GPS sensors. Finally, fixed tethers provide unlimited power but eliminate the drone's mobility.

AutoCharge addresses these challenges by decoupling the landing process from the electrical connection process. The system provides a universal, low-cost ($50), and portable solution that is robust enough to handle the "wobble" of a drone landing in dynamic environments.

System Design and Methodology

The AutoCharge system comprises two primary components: a compact, portable ground station and a lightweight charging tether that dangles from the quadrotor's undercarriage.

1. Orientation-Agnostic Connectors

To eliminate the need for precise heading alignment, the system utilizes custom-designed circular magnetic connectors. These concentric ring contacts allow the drone to establish a reliable electrical connection regardless of its orientation (0–360°) upon landing. This significantly reduces the computational load on the flight controller during the docking phase.

2. Active Electromagnet (EM) Guidance

The ground station is equipped with a powerful electromagnet that acts as a "magnetic funnel." As the drone descends and the dangling tether enters the proximity of the station, the EM is activated. The resulting magnetic field pulls the tether into the center of the dock, compensating for lateral positioning errors of up to several centimeters. This mechanical buffer ensures a successful mate even when the drone's landing is imperfect.

3. Smart Docking Logic

The docking sequence is managed by an onboard Arduino Nano on the ground station. Once the tether is physically mated, the system detects current flow and deactivates the electromagnet to conserve power and prevent electromagnetic interference with the drone's sensors. The station then initiates a standard balance-charging cycle. Upon reaching full charge, the drone initiates takeoff; because the EM is inactive, the residual magnetic force of the permanent magnets is easily overcome by the quadrotor's vertical thrust.

Experimental Evaluation

The system was evaluated through a series of physical experiments designed to test its robustness and efficiency in various environments.

  • Indoor and Outdoor Trials: Indoor tests utilized a Vicon motion capture system for high-precision ground-truth positioning, while outdoor trials were conducted on a rooftop terrace to subject the system to real-world wind disturbances and GPS inaccuracies.
  • Long-Duration Missions: To demonstrate the "perpetual" nature of the system, the authors conducted a 10-hour continuous flight log. During this period, the drone autonomously cycled between flight tasks and docking/charging phases without human intervention.
  • Magnet Optimization: The study compared three different magnet configurations (Neodymium vs. Ceramic). Results indicated a clear trade-off: while heavier magnets reduced total flight time by approximately 15%, they increased the effective "pull-in" distance by a factor of five, making them more suitable for high-wind outdoor missions.

Key Results and Insights

AutoCharge demonstrated a 100% docking success rate when the tether was within the designated docking area (up to 25cm for the largest magnet configuration) across over 100 iterations. By utilizing direct contact via pogo-pins rather than induction, the system maintained the high charging efficiency of a standard wall-connected balance charger.

Furthermore, the system's low cost—under $50 for the entire assembly—stands in stark contrast to commercial docking stations that can cost tens of thousands of dollars. The hardware is also highly adaptable, having been successfully tested on both 2S and 4S LiPo configurations, suggesting universal compatibility with various quadrotor frames.

Discussion and Future Work

While AutoCharge represents a significant step toward autonomous persistence, several areas for improvement remain. The dangling tether introduces complex cable-suspended payload dynamics; while these did not significantly degrade stability in current tests, future work will involve formal mathematical modeling of these dynamics to optimize flight control.

Additionally, the current reliance on external localization (Vicon or GPS) limits deployment in unknown environments. The authors intend to integrate onboard computer vision for visual servoing, allowing the drone to detect and navigate to the dock autonomously. Finally, scaling the system for larger industrial drones will require larger connectors and enhanced thermal management to handle higher charging currents.

Summary updated

Abstract

Battery endurance represents a key challenge for long-term autonomy and long-range operations, especially in the case of aerial robots. In this paper, we propose AutoCharge, an autonomous charging solution for quadrotors that combines a portable ground station with a flexible, lightweight charging tether and is capable of universal, highly efficient, and robust charging. We design and manufacture a pair of circular magnetic connectors to ensure a precise orientation-agnostic electrical connection between the ground station and the charging tether. Moreover, we supply the ground station with an electromagnet that largely increases the tolerance to localization and control errors during the docking maneuver, while still guaranteeing smooth un-docking once the charging process is completed. We demonstrate AutoCharge on a perpetual 10 hours quadrotor flight experiment and show that the docking and un-docking performance is solidly repeatable, enabling perpetual quadrotor flight missions.
BibTeX
@inproceedings{saviolo2023autocharge,
  author = {Alessandro Saviolo and Jeffrey Mao and Roshan Balu T. M. B and Vivek Radhakrishnan and Giuseppe Loianno},
  title = {{AutoCharge: Autonomous Charging for Perpetual Quadrotor Missions}},
  booktitle = {IEEE International Conference on Robotics and Automation},
  year = {2023},
  url = {https://openreview.net/forum?id=fefAeTnaDm},
}
Figure