Application of Design of Experiment Method for Thrust Force Minimization in Step-feed Micro Drilling

Dongwoo Kim, Myeong‐Woo Cho, Тае-Il Seo, Eung-Sug LeeSensors 2008 · DOI

TL;DR

This paper tackles the challenge of minimizing thrust forces during micro-drilling of small holes, a critical process for advanced manufacturing. By applying Design of Experiments (DOE) and ANOVA, the researchers identified that feedrate is the most significant factor in reducing these forces, leading to optimized drilling conditions for improved precision and efficiency.

What Problem Does This Paper Address?

The increasing demand for miniaturized components in fields like medical instruments and aerospace engineering necessitates the creation of smaller, deeper holes with high aspect ratios. Traditional micro-drilling methods struggle with these demands, often leading to issues like poor chip evacuation, excessive heat, drill wandering, and high cutting forces (thrust). These problems can degrade the quality of the drilled holes and even lead to drill breakage. The paper specifically addresses the challenge of minimizing the thrust force, a key indicator of drilling difficulty and potential for damage, in a step-feed micro-drilling process.

Methods

The core of this research lies in the application of the Design of Experiments (DOE) methodology, specifically using the Taguchi method. This approach aims to efficiently identify optimal process parameters by minimizing the number of experiments required. The authors employed an L<sub>27</sub>(3<sup>13</sup>) orthogonal array to design their experiments. This array allows for the systematic investigation of three factors (feedrate, step-feed, and spindle RPM) at three different levels each, while also accounting for potential interactions between them.

Following the experimental runs, Analysis of Variance (ANOVA) was used to statistically analyze the collected data. ANOVA helps to determine which factors have a significant impact on the drilling thrust and to quantify their influence. The researchers also utilized Signal-to-Noise (S/N) ratios as a performance measure, focusing on the "Smaller the Better" characteristic to minimize drilling thrust.

Datasets

Not discussed in the paper. The study relies on experimental data generated from the micro-drilling process itself, rather than pre-existing datasets.

Key Insights and Ideas

  • Feedrate Reigns Supreme: The most impactful finding is that feedrate is the dominant factor in minimizing drilling thrust during step-feed micro-drilling. This suggests that controlling how quickly the drill advances is more critical than spindle speed or the step-feed parameters for reducing forces.
  • Step-Feed's Role: While feedrate is primary, step-feed and spindle RPM also play significant roles, though to a lesser extent. The research provides a clear hierarchy of influence.
  • DOE Efficiency: The study demonstrates the power of DOE, particularly the Taguchi method, in efficiently optimizing complex processes. By using an orthogonal array, they were able to gain significant insights with a manageable number of experiments.
  • No Significant Interactions: Interestingly, the analysis revealed no significant interactions between the tested factors (A*B and A*C). This simplifies the optimization process, as the effect of each factor can be considered largely independent.

Key Results

The study successfully identified optimal drilling conditions for minimizing thrust force. Based on the S/N ratio analysis and ANOVA, the optimal settings were determined to be:

  • Factor A (Feedrate): Level 1 (A1)
  • Factor B (Step-feed): Level 3 (B3)
  • Factor C (Spindle RPM): Level 3 (C3)

The ANOVA results indicated that feedrate (A) had the highest F-value (65.3), signifying its strongest influence on drilling thrust, followed by step-feed (B) and spindle RPM (C). The paper also presents visual representations of the S/N ratio responses and interaction graphs, illustrating these findings.

Limitations and Future Work

The authors acknowledge that this study focused solely on minimizing drilling thrust as the primary objective. They suggest that future work could expand to consider other critical factors for micro-drilling, such as:

  • Drill life: How long the drill can be used before performance degrades.
  • Surface roughness: The quality of the machined hole's inner surface.
  • Circularity: How perfectly round the drilled hole is.
  • Drilling time: The overall efficiency of the process.
  • Burr formation: The presence of material remnants around the hole edge.

Furthermore, the authors plan to investigate the influence of interactions among factors in their subsequent research, which was not found to be significant in this particular study.

Summary updated

Abstract

Micro drilled holes are utilized in many of today's fabrication processes.Precision production processes in industries are trending toward the use of smaller holeswith higher aspect ratios, and higher speed operation for micro deep hole drilling. However,undesirable characteristics related to micro drilling such as small signal-to-noise ratios,wandering drill motion, high aspect ratio, and excessive cutting forces can be observedwhen cutting depth increases. In this study, the authors attempt to minimize the thrustforces in the step-feed micro drilling process by application of the DOE (Design ofExperiment) method. Taking into account the drilling thrust, three cutting parameters,feedrate, step-feed, and cutting speed, are optimized based on the DOE method. Forexperimental studies, an orthogonal array L<sub>27</sub>(3<sup>13</sup>) is generated and ANOVA (Analysis ofVariance) is carried out. Based on the results it is determined that the sequence of factorsaffecting drilling thrusts corresponds to feedrate, step-feed, and spindle rpm. Acombination of optimal drilling conditions is also identified. In particular, it is found in thisstudy that the feedrate is the most important factor for micro drilling thrust minimization.
BibTeX
@inproceedings{kim2008application,
  author = {Dongwoo Kim and Myeong‐Woo Cho and Тае-Il Seo and Eung-Sug Lee},
  title = {{Application of Design of Experiment Method for Thrust Force Minimization in Step-feed Micro Drilling}},
  booktitle = {Sensors},
  year = {2008},
  doi = {10.3390/s8010211},
}
Figure