Abstract
The use of lignin, a by-product of the pulp and paper industry, in asphalt binder development offers significant environmental and economic benefits. This study evaluates lignin-modified asphalt binders with concentrations ranging from 3% to 15%. Using Fourier transform infrared spectroscopy (FTIR), dynamic shear rheometer (DSR), and thermogravimetry (TG), the research analyzes the mechanisms behind improved high-temperature stability. Results indicate that lignin modification is a physical blending process. Increasing lignin content enhances the complex shear modulus ($G^*$) and anti-rutting performance ($G^*/\sin\delta$), with an optimal threshold identified at 12%. Thermal analysis reveals that lignin’s lower decomposition rate and higher residual mass compared to asphalt are key factors in enhancing binder stability within the service temperature range of 25°C to 200°C.
Introduction
Asphalt pavements are susceptible to thermal stress, particularly at high temperatures where the binder's viscosity decreases, leading to permanent deformations known as "rutting." While synthetic polymers are traditionally used to enhance binder stiffness, there is an increasing demand for sustainable, bio-based alternatives. Lignin, the second most abundant natural polymer and a major byproduct of the paper industry, presents a promising "green" modifier. This study investigates the chemical and physical mechanisms by which lignin improves asphalt's thermal stability and identifies the optimal concentration for performance.
Materials and Methods
The experimental program utilized 70# base asphalt and commercial lignin (85–90% purity). Modified binders were prepared with lignin concentrations of 3%, 6%, 9%, 12%, and 15% by mass.
The blending process involved high-speed shearing at 5000 rpm for one hour at a temperature of 150°C. The resulting samples were analyzed using three primary techniques:
- Fourier Transform Infrared Spectroscopy (FTIR): Used to identify functional groups and determine if the lignin reacted chemically with the asphalt or simply mixed with it physically.
- Dynamic Shear Rheometer (DSR): Used to measure the viscoelastic properties, specifically the complex shear modulus ($G^*$) and phase angle ($\delta$), which indicate stiffness and elasticity.
- Thermogravimetry (TG/DTG): A thermal analysis technique that measures mass loss as a function of temperature to evaluate the decomposition rates and residual carbon of the materials.
Results and Discussion
Modification Mechanism
FTIR analysis revealed no new characteristic absorption peaks in the lignin-modified samples. While peaks associated with lignin increased in intensity with higher concentrations, the lack of new chemical bonds suggests that the modification is a purely physical blending process. Lignin acts as a reinforcing filler within the asphalt matrix rather than a chemical reactant.
Rheological Performance and the 12% Threshold
The addition of lignin significantly altered the viscoelastic behavior of the binder. As lignin content increased, the complex shear modulus ($G^*$) rose and the phase angle ($\delta$) decreased, indicating the asphalt became stiffer and more elastic. Consequently, the anti-rutting factor ($G^*/\sin\delta$) improved. However, the researchers observed that these benefits began to plateau after a 12% lignin concentration. Adding 15% lignin provided diminishing returns and could potentially lead to binder saturation, which might negatively impact other properties like low-temperature cracking.
Thermal Stability and Decomposition
Thermogravimetric analysis provided insight into the superior thermal backbone provided by lignin. At 700°C, asphalt retains only approximately 16% of its mass, whereas lignin retains about 68%. This high residual carbon content helps the binder resist decomposition. The study found that the maximum mass loss rate for asphalt occurs at 455°C (4.5%/°C), while lignin’s maximum loss rate is much lower (1.2%/°C) and occurs earlier at 345°C. Within the standard service temperature range (25°C–200°C), lignin has a consistently positive effect on the thermal stability of the overall binder.
Conclusion
Lignin is an effective, sustainable modifier that enhances the high-temperature stability and rutting resistance of asphalt binders through physical reinforcement. A 12% lignin concentration was identified as the optimal balance for performance. While these findings are promising for high-temperature durability, future work should address the potential impact of increased binder stiffness on ductility and low-temperature performance to ensure balanced pavement longevity.
Summary updated