An Impedance Sensing Platform for Monitoring Heterogeneous Connectivity and Diagnostics in Lab-on-a-Chip Systems

Chunjie Zhang, Yang Su, Siyi Hu, Kai Jin, Yuhan Jie, Wenshi Li, Arokia Nathan, Hanbin Ma

TL;DR

This paper introduces a novel impedance sensing platform that can seamlessly integrate with lab-on-a-chip (LOC) systems, specifically digital microfluidics (DMF), to provide real-time monitoring of hardware connections. This system not only detects faulty connections in milliseconds but can also pinpoint droplet locations, addressing a critical need for reliable diagnostics in complex, heterogeneous integrated systems.

What Problem Does This Paper Address?

Heterogeneous integrated systems, which combine different electronic technologies (like CMOS, IGBTs, TFTs) on a single platform, are crucial for developing advanced functionalities. A prime example is digital microfluidics (DMF), which integrates microelectromechanical systems (MEMS) with drive electronics for precise liquid manipulation. However, these systems rely on numerous physical connections between the microfluidic device and the external control electronics. Verifying the reliability of these hundreds or even thousands of connections is a significant challenge. Traditional methods like visual inspection are insufficient for the dense interconnections in DMF systems. Furthermore, biofouling can necessitate frequent replacement of disposable DMF chips, making connection reliability checks after each setup essential. The paper addresses the critical need for a non-intrusive, real-time method to monitor the integrity of these connections and diagnose system status.

Methods

The core of the proposed solution is an impedance sensing platform integrated into the DMF system. The sensing unit is placed between the top electrode of the DMF device and the microcontroller (MCU). The system utilizes a square-wave voltage stimulus (0-300V, up to 200 kHz) to probe the impedance of each connection.

Key components of the sensing unit include:

  • Voltage Buffer: Provides sufficient driving capability for subsequent stages.
  • RC Circuit (DUT + Sensor Frontend): Forms a high-pass filter.
  • RC Differentiator: Converts the input square wave into a signal with positive and negative components.
  • Non-inverting Summing Amplifier: Levels up the output signal.
  • Voltage Divider: Connects to the MCU's analog-to-digital converter (ADC).

The processed signal is then analyzed by the MCU using a Fast Fourier Transform (FFT) to extract the magnitude of the output signal at the stimulus frequency. This magnitude is then compared against pre-set thresholds:

  • Threshold t₁: Differentiates between a good connection and an open circuit (bad connection).
  • Threshold t₂: Differentiates between the presence of an aqueous droplet and the surrounding medium (e.g., silicon oil or air).

The system is implemented on an STM32 microcontroller, capable of controlling up to 180 channels and performing measurements at a 200 kHz sampling rate. The software interface, developed in MATLAB, visualizes the status of each electrode with color codes (blue for bad connection, white for medium, red for droplet).

Datasets

The paper does not explicitly mention training datasets. Instead, it describes experiments conducted on a fabricated DMF device with an 8x8x8 hexagonal electrode array (169 electrodes). The evaluation involves measuring the impedance of these electrodes under different conditions:

  • Open Circuit (DUT1): Simulating a disconnected electrode.
  • Silicon Oil Medium (DUT2): Simulating the presence of the surrounding medium.
  • Aqueous Droplet (DUT3): Simulating the presence of a liquid sample.

The paper also mentions testing seven different samples (DI water, ethanol, PBS, BSA, NaCl, oleylamine, octadecene) at various frequencies to determine optimal detection frequencies, suggesting a form of empirical dataset generation for optimization.

Key Insights and Ideas

  • Impedance as a Universal Diagnostic Tool: The paper demonstrates that impedance sensing, a well-established technique, can be effectively adapted for real-time monitoring of physical connections in complex LOC systems, a problem not easily solved by traditional methods.
  • Seamless Integration: The sensing platform is designed to be integrated directly into existing DMF driving electronics, minimizing hardware modifications and enabling a plug-and-play solution.
  • Dual Functionality: The same impedance sensing setup can serve two critical purposes: verifying connection integrity and determining droplet location, thereby enhancing system diagnostics and operational control.
  • Speed and Efficiency: The use of FFT for signal processing allows for rapid detection (under 2 ms per channel), making real-time monitoring feasible even for systems with hundreds of connections.
  • Robustness to Noise: FFT analysis in the frequency domain helps filter out noise and isolate the relevant signal, improving sensing accuracy.

Key Results

  • Connectivity Detection: The system successfully distinguished between open circuits (bad connections) and connected electrodes with high confidence. Threshold t₁ was used to identify bad connections, indicated by blue shading in the MATLAB interface.
  • Droplet Location: The system could differentiate between an aqueous droplet and the surrounding medium (silicon oil or air) using threshold t₂. This was visualized with red (droplet) and white (medium) shading.
  • Measurement Speed: Single-channel detection time was less than 2 ms. For a 169-electrode system, the overall detection time was approximately 300 ms.
  • Frequency Optimization: Different liquid samples showed optimal detection sensitivities at specific frequencies (e.g., 12 kHz for DI water, 10 kHz for oleylamine, 30 kHz for octadecene), suggesting the potential for frequency multiplexing to detect multiple samples simultaneously.
  • Uniformity: Measurements across all 169 electrodes showed high uniformity, indicating the reliability of the sensing approach.

Limitations and Future Work

  • Threshold Calibration: The paper mentions pre-set thresholds (t₁ and t₂). The process for determining these optimal thresholds for various conditions and samples could be further elaborated.
  • Scalability: While the system is designed to be scalable, the paper focuses on a 169-electrode system. Further investigation into scaling to thousands of connections would be valuable.
  • Complex Media: The current work focuses on simple media like DI water and silicon oil. Future work could explore the detection of more complex biological or chemical samples and their interactions.
  • Environmental Factors: The impact of environmental factors (temperature, humidity) on impedance measurements and the robustness of the system under such conditions are not discussed.
  • Future Directions: The authors suggest that the impedance-based sensing platform has the potential to be applied to other heterogeneous integrated systems that require real-time monitoring and diagnostics of multiconnectivity. This opens avenues for its use in diverse fields beyond microfluidics.

Summary updated

Abstract

Reliable hardware connectivity is vital in heterogeneous integrated systems. For example, in digital microfluidics lab-on-a-chip systems, there are hundreds of physical connections required between a microelectromechanical fabricated device and the driving system that can be remotely located on a printed circuit board. Unfortunately, the connection reliability cannot be checked or monitored by vision-based detection methods that are commonly used in the semiconductor industry. Therefore, a sensing platform that can be seamlessly integrated into existing digital microfluidics systems and provide real-time monitoring of multiconnectivity is highly desired. Here, we report an impedance sensing platform that can provide fast detection of a single physical connection in timescales of milliseconds. Once connectivity is established, the same setup can be used to determine the droplet location. The sensing system can be scaled up to support multiple channels or applied to other heterogeneously integrated systems that require real-time monitoring and diagnostics of multiconnectivity systems.
BibTeX
@inproceedings{zhang2020impedance,
  author = {Chunjie Zhang and Yang Su and Siyi Hu and Kai Jin and Yuhan Jie and Wenshi Li and Arokia Nathan and Hanbin Ma},
  title = {{An Impedance Sensing Platform for Monitoring Heterogeneous Connectivity and Diagnostics in Lab-on-a-Chip Systems}},
  booktitle = {ACS},
  year = {2020},
  doi = {10.1021/acsomega.9b04048},
}

Loading related content...

Figure