An Experimental Study on the Behavior of Capping Material by Sea Waves

Jin-Young Kong, Young‐Tak Kim, Jae‐Mo Kang, Jangguen LeeJournal of the Korean Geoenvironmental Society 2014 · DOI

Abstract

In-situ capping is a method to stabilize contaminated sediments by isolation. Few researches on the in-situ capping have been performed, although the engineering approach is still required to prevent the release of contaminants. In this study, hydraulic model tests were conducted by using a wave generator to observe the change of cap thickness, which is an important factor in capping design. Sands with particle sizes between 0.075 to 2 mm were used as capping materials to observe the change of capping thickness by waves at a 1:10 scale. The experimental results show that the surface of capping materials deforms similarly to the wave form. As wave height increases, the erosion of capping materials generally increases.

Introduction

Coastal sediment contamination is a significant environmental challenge. While dredging is a common remediation strategy, it is often costly and risks the re-suspension of pollutants. In-situ capping offers a less invasive alternative by placing a layer of clean material, such as sand, over the contaminated site to isolate it physically and chemically. However, the long-term stability of these caps against hydrodynamic forces, particularly sea waves, is a critical design concern. This study experimentally investigates how wave height and frequency influence the erosion and deformation of sand caps to ensure they remain effective over time.

Methodology

The research utilized a 1:10 scale hydraulic model in a 56-meter-long wave flume. The experimental setup included a wave generator at one end and wave absorption at the other to minimize reflections.

Schematic of the experimental setup in the wave flume showing gage locations and the 1:40 slope.

Materials and Placement

Clean sand with particle sizes ranging from 0.075 to 2 mm was selected as the capping material. To simulate the "grab dredging" method used in field applications, a custom-built sand rainfall device was employed to deposit sand into the water in controlled batches (10, 20, and 30 kgf).

Experimental Conditions

The team simulated "regular waves" corresponding to a 50-year return period storm. Model wave heights ranged from 0.1m (design standard) to 0.3m (simulating a 3.0m prototype wave). Topographical changes were measured using the Shape Metrix 3D system, a photogrammetry technique that reconstructs the 3D surface of the sand cap from multiple photographs, providing high-precision data on erosion and ripple formation.

Results and Discussion

The physical experiments provided clear visual and quantitative evidence of how sand caps respond to wave energy.

Physical model test in progress, showing the sand cap deformation under wave action.

Ripple Formation and Deformation

Upon exposure to waves, the initially smooth sand surface deformed into a series of ripples. These ripples mirrored the wave form, with their length increasing proportionally to the wave height. Interestingly, the initial placement method (batch size) had a negligible effect on the final settled geometry, suggesting operational flexibility for contractors.

Erosion Patterns

Erosion was most pronounced at the center of the cap, where the material was highest. Waves effectively redistributed sand from the crest toward the edges, causing the cap to become thinner and wider. Under extreme conditions (3.0m prototype wave), the cap experienced significant erosion, losing 50% to 72% of its initial thickness. The maximum erosion depth measured was 0.077m in the model (0.77m prototype).

Stability Validation

Crucially, the 50-year design wave (1.0m prototype) resulted in minimal observable erosion. This validates current engineering standards for the studied location, confirming that a properly designed 1.0-meter cap can withstand standard storm conditions without exposing underlying contaminants.

Conclusion

This experimental study demonstrates that while extreme wave events can significantly erode sand caps, standard design practices are robust. The use of 3D photogrammetry allowed for a detailed understanding of ripple formation and material redistribution. Future research should address the interaction between the sand cap and soft underlying "muck," as well as the long-term effects of bioturbation and irregular sea states.

Summary updated

Abstract

피복공법은 해저 퇴적오염물질을 차단하고 안정화시켜 처리하는 방안이다. 국내에서는 피복공법에 대한 연구가 부족하나, 오염물질이 방출되지 않기 위한 공학적 접근법이 반드시 필요하다. 본 연구에서는 피복설계 시 중요 인자인 피복재 침식을 확인하기 위해 조파장치를 이용한 수리모형실험을 실시하였다. 1:10의 실험축척을 적용하여 0.07~2 mm 크기의 모래를 피복 재료로 사용하였고, 모형 수조 내 강사한 후 파랑을 발생시켜 피복재의 형상변화를 관측하였다. 실험결과, 피복재의 표면은 파랑의 파형과 유사하게 변형이 발생하였으며, 파랑의 파고가 증가할수록 대체적으로 침식되는 피복재의 깊이가 증가하였다. In-situ capping is a method to stabilize contaminated sediments by isolation. Few researches on the in-situ capping have been performed, although the engineering approach is still required to prevent the release of contaminants. In this study, hydraulic model test were conducted by using a wave generator to observe the change of cap thickness which is important factor in design of capping. Sands with particle size between 0.075 to 2 mm as capping materials were used to observe the change of capping thickness by waves. The experimental results show that the surface of capping materials is similar to wave form. The more wave height increases, the more erosion of capping materials increases.
BibTeX
@article{kong2014experimental,
  author = {Jin-Young Kong and Young‐Tak Kim and Jae‐Mo Kang and Jangguen Lee},
  title = {{An Experimental Study on the Behavior of Capping Material by Sea Waves}},
  journal = {Journal of the Korean Geoenvironmental Society},
  year = {2014},
  doi = {10.14481/jkges.2014.15.7.51},
}
Figure