Achieving Full-Bandwidth Sensing Performance with Partial Bandwidth Allocation for ISAC

Zhiqiang Xiao, Zhiwen Zhou, Qianglong Dai, Yong Zeng, Fei Yang, Yan Chen

TL;DR

This paper introduces a Two-Stage Delay Estimation (TSDE) method for Integrated Sensing and Communication (ISAC) systems that allows a user to achieve "full-bandwidth" sensing resolution while only being allocated a fraction of the actual bandwidth. By cleverly switching between contiguous and distributed subcarrier allocations, the system overcomes the traditional trade-off between sensing resolution and range ambiguity.

What Problem Does This Paper Address?

In the upcoming 6G era, Integrated Sensing and Communication (ISAC) aims to use cellular infrastructure not just for talking, but for "seeing" the environment (radar-like sensing). A major hurdle is bandwidth allocation. In a multi-user system, a single user is typically only given a small slice (fractional bandwidth) of the total spectrum.

In radar physics, bandwidth equals resolution: the narrower your bandwidth, the harder it is to distinguish between two objects close together (delay resolution). While researchers can use "distributed" subcarriers (spacing them out across the whole spectrum) to improve resolution, this creates "ghost targets" or grating lobes—a phenomenon known as delay ambiguity. The authors tackle a fundamental question: Can we get the high resolution of a wide pipe and the clear, unambiguous range of a narrow pipe, all while using only a fraction of the total bandwidth?

Methods

The authors propose a Two-Stage Delay Estimation (TSDE) algorithm using the DFT-s-OFDM waveform (a standard in 4G and 5G).

  1. Stage 1: Coarse Estimation. The user transmits signals using collocated (contiguous) subcarriers. This provides a very large "unambiguous range"—meaning we can see far without seeing ghosts—but the resolution is poor. This stage identifies the general "bins" or regions where targets are located.
  2. Stage 2: Refined Estimation. The user then transmits using distributed (decimated) subcarriers. By skipping subcarriers and spreading them out, the signal effectively "mimics" a much wider bandwidth, drastically improving resolution.
  3. The Secret Sauce: Normally, Stage 2 would produce ambiguous "ghost" results. However, the TSDE method uses the coarse results from Stage 1 to create a "protection region." It only looks for targets in the specific areas identified in Stage 1, effectively ignoring the ghost targets that fall outside those regions.

The authors also derive an optimal decimation factor ($\eta^*$) to ensure that the "ghosts" created in Stage 2 are mathematically guaranteed to fall outside the search area identified in Stage 1.

Datasets

The paper relies on numerical simulations rather than a physical dataset. They modeled a system with:

  • Subcarrier Spacing: 120 kHz.
  • Total Subcarriers ($K$): 1024 (Total bandwidth of ~122.88 MHz).
  • Allocated Subcarriers ($K_1$): 32 (Only ~3.84 MHz).
  • Channel Model: A multi-path environment where the algorithm's ability to detect the number of paths and their specific delays was tested via Monte Carlo simulations.

Key Insights and Ideas

  • Virtual Bandwidth Expansion: You don't need to occupy every hertz of a 100MHz band to get 100MHz-level resolution. By using a sparse (decimated) pattern, you can achieve the same "sharpness" in your delay estimation.
  • The Power of Two Stages: The "aha moment" is realizing that sensing doesn't have to happen in a single snapshot. By using a coarse-to-fine approach, you can resolve the ambiguity problem that has traditionally plagued sparse frequency sensing.
  • Efficiency Gains: The paper mathematically proves that if the environment's "clutter" (channel delay spread) is less than half the unambiguous range, you can achieve full-bandwidth performance using at most half of the actual bandwidth. In some scenarios, using just the square root of the total subcarriers ($\sqrt{K}$) is sufficient.

Key Results

  • Resolution Parity: The TSDE method achieved the same delay resolution as a system using the full 122.88 MHz bandwidth, despite only using 3.84 MHz (about 3% of the total).
  • Detection Accuracy: At a Signal-to-Noise Ratio (SNR) of 10 dB or higher, the proposed method's probability of correct detection ($P_d$) and estimation error (NMSE) matched the performance of the "ideal" full-bandwidth case.
  • Superiority over Conventional Methods: Compared to standard contiguous allocation (which is what most 5G systems use today), the TSDE method showed significantly lower estimation errors and much higher resolution for the same amount of power and bandwidth.

Limitations and Future Work

  • Latency and Overhead: Because the method requires two distinct stages (two transmissions), it introduces more overhead and latency than a single-shot estimation. This might be a challenge for extremely high-speed mobility scenarios.
  • Static Channel Assumption: The algorithm assumes the environment doesn't change significantly between Stage 1 and Stage 2. If a target moves too fast, the "protection region" from Stage 1 might become invalid.
  • Future Directions: The authors suggest that this logic could be extended to Doppler estimation (sensing speed) and could be integrated into more complex multi-user interference environments.

Summary updated

Abstract

This letter studies an uplink integrated sensing and communication (ISAC) system using discrete Fourier transform spread orthogonal frequency division multiplexing (DFT-s-OFDM) transmission. We try to answer the following fundamental question: With only a fractional bandwidth allocated to the user with sensing task, can the same delay resolution and unambiguous range be achieved as if all bandwidth were allocated to it? We affirmatively answer the question by proposing a novel two-stage delay estimation (TSDE) method that exploits the following facts: without increasing the allocated bandwidth, higher delay resolution can be achieved via distributed subcarrier allocation compared to its collocated counterpart, while there is a trade-off between delay resolution and unambiguous range by varying the decimation factor of subcarriers. Therefore, the key idea of the proposed TSDE method is to first perform coarse delay estimation with collocated subcarriers to achieve a large unambiguous range, and then use distributed subcarriers with optimized decimation factor to enhance delay resolution while avoiding delay ambiguity. Our analysis shows that the proposed TSDE method can achieve the full-bandwidth delay resolution and unambiguous range, by using only at most half of the full bandwidth, provided that the channel delay spread is less than half of the unambiguous range. Numerical results show the superiority of the proposed method over the conventional method with collocated subcarriers.
BibTeX
@misc{xiao2024achieving,
  author = {Zhiqiang Xiao and Zhiwen Zhou and Qianglong Dai and Yong Zeng and Fei Yang and Yan Chen},
  title = {{Achieving Full-Bandwidth Sensing Performance with Partial Bandwidth Allocation for ISAC}},
  year = {2024},
  eprint = {2412.20083},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2412.20083},
}
Figure