A Tale of Two Sides of Wafer: Physical Implementation and Block-Level PPA on Flip FET with Dual-sided Signals

Haoran Lu, Xun Jiang, Yanbang Chu, Ziqiao Xu, Rui Guo, Wanyue Peng, Yibo Lin, Runsheng Wang, Heng Wu, Ru Huang

TL;DR

The Flip FET (FFET) is a breakthrough transistor architecture that combines 3D stacking with a fully functional wafer backside, enabling signals and power to be routed on both sides of the silicon. This paper presents the first comprehensive block-level evaluation, demonstrating that FFETs can achieve a 23.3% core area reduction and a 25% frequency boost over state-of-the-art Complementary FETs (CFETs).

What Problem Does This Paper Address?

As semiconductor scaling approaches the physical limits of traditional 2D layouts, the industry is turning to 3D transistor stacking (like CFETs) and Backside Power Delivery Networks (BSPDN). However, CFETs face a major hurdle: routing congestion. Stacking transistors vertically dramatically increases pin density, making it incredibly difficult to connect everything using only the front side of the wafer.

While researchers have proposed moving signals to the backside, current architectures like CFET are asymmetric, making backside pins difficult to implement without area-intensive "bridging cells." The authors address this by evaluating the Flip FET (FFET), a symmetric architecture that naturally supports dual-sided pins and routing, potentially unlocking the next level of Power-Performance-Area (PPA) gains.

Fig. 1. Scaling roadmap from FinFET to Nanosheet FET, CFET and FFET.

Methods

The researchers developed a full-spectrum physical implementation and PPA evaluation framework for FFETs. Key components include:

  • Symmetric Cell Design: Unlike CFETs, FFETs consist of nFET and pFET pairs stacked back-to-back. This symmetry allows for identical FEOL (Front-End-of-Line) and BEOL (Back-End-of-Line) structures on both sides.
  • Split Gate Technology: The separated front and backside processes enable "Split Gates," where stacked transistors can be controlled by two different signals without extra area. This is particularly beneficial for complex logic like Transmission Gates and $C^2MOS$ circuits.
  • Dual-Sided Routing Algorithm: A novel flow that partitions the netlist into frontside and backside nets based on optimized pin locations, performing global and detailed routing independently on both sides.
  • Power Planning with Tap Cells: To connect frontside power rails to the backside delivery network, the authors introduced "Power Tap Cells" that route VSS around VDD rails using intra-cell metals.
  • Dual-Sided RC Extraction: A method to merge design exchange format (DEF) files from both sides to accurately calculate parasitics for timing analysis.
Fig. 2. (a) 3D structure of a 3.5T FFET standard cell with two-fin transistors, taking INVD1 as an example, based on [12]. (b) Cross-sections along the gate region (A-A’) and source-drain region (B-B’).

Datasets

To validate their framework, the authors used:

  • Benchmark Design: A 32-bit RISC-V core.
  • Technology Node: A virtual 5nm node PDK.
  • Standard Cell Library: A custom-designed library featuring 3.5T (track) FFET cells compared against 4T CFET cells.

Key Insights and Ideas

  • Symmetry Solves Congestion: By providing pins on both sides, FFET effectively doubles the available routing "real estate." This reduces pin density on the front side, which is the primary bottleneck for CFET scaling.
  • The "Split Gate" Bonus: In sequential logic like D-Flip-Flops (DFFs), the Split Gate allows for significant area savings. For a $C^2MOS$ circuit, FFET saves 1 CPP (Contacted Poly Pitch) compared to CFET because it doesn't need extra space to route complementary clock signals to the same vertical stack.
  • Cost-Friendly Scaling: The study found that FFET performance remains robust even when reducing the number of metal routing layers. A design with only 5 layers per side performed nearly as well as one with 12, offering a path to high performance with lower manufacturing complexity.
Comparison of C2MOS implementation: FFET (2 CPP) vs CFET (3 CPP) thanks to the Split Gate.

Key Results

The block-level evaluation of the RISC-V core yielded impressive results when comparing 3.5T FFET to 4T CFET:

  • Area: 23.3% reduction in post-P&R core area at the same utilization.
  • Performance: 25.0% higher frequency at the same utilization level (76%).
  • Power: 11.9% lower power consumption at the same frequency.
  • Dual-Sided Gain: By specifically optimizing for dual-sided signal routing, the researchers achieved an additional 10.6% frequency gain without any power degradation.
  • Utilization: FFET reached a maximum utilization of 86%, significantly higher than the routability limits typically seen in ultra-scaled CFET designs.

Limitations and Future Work

  • Power Plan Constraints: The current maximum utilization (86%) is limited by the physical placement of Power Tap Cells rather than routing congestion. Future work could optimize these power structures to push density even further.
  • Cell-Specific Overheads: A few specific cell types (like AOI22/OAI22) showed slight area degradation due to the need for extra "Drain Merge" vias.
  • Manufacturing Complexity: While the PPA benefits are clear, the practical manufacturing of back-to-back stacked transistors with dual-sided BEOL remains a significant challenge for high-volume production.

Summary updated

Abstract

As the conventional scaling of logic devices comes to an end, functional wafer backside and 3D transistor stacking are consensus for next-generation logic technology, offering considerable design space extension for powers, signals or even devices on the wafer backside. The Flip FET (FFET), a novel transistor architecture combining 3D transistor stacking and fully functional wafer backside, was recently proposed. With symmetric dual-sided standard cell design, the FFET can deliver around 12.5% cell area scaling and faster but more energy-efficient libraries beyond other stacked transistor technologies such as CFET. Besides, thanks to the novel cell design with dual-sided pins, the FFET supports dual-sided signal routing, delivering better routability and larger backside design space. In this work, we demonstrated a comprehensive FFET evaluation framework considering physical implementation and block-level power-performance-area (PPA) assessment for the first time, in which key functions are dual-sided routing and dual-sided RC extraction. A 32-bit RISC-V core was used for the evaluation here. Compared to the CFET with single-sided signals, the FFET with single-sided signals achieved 23.3% post-P&R core area reduction, 25.0% higher frequency and 11.9% lower power at the same utilization, and 16.0 % higher frequency at the same core area. Meanwhile, the FFET supports dual-sided signals, which can further benefit more from flexible allocation of cell input pins on both sides. By optimizing the input pin density and BEOL routing layer number on each side, 10.6% frequency gain was realized without power degradation compared to the one with single-sided signal routing. Moreover, the routability and power efficiency of FFET barely degrades even with the routing layer number reduced from 12 to 5 on each side, validating the great space for cost-friendly design enabled by FFET.
BibTeX
@inproceedings{lu2025tale,
  author = {Haoran Lu and Xun Jiang and Yanbang Chu and Ziqiao Xu and Rui Guo and Wanyue Peng and Yibo Lin and Runsheng Wang and Heng Wu and Ru Huang},
  title = {{A Tale of Two Sides of Wafer: Physical Implementation and Block-Level PPA on Flip FET with Dual-sided Signals}},
  booktitle = {DATE},
  year = {2025},
  doi = {10.23919/date64628.2025.10993282},
}
Figure