A Real-Time Monitoring System of Industry Carbon Monoxide Based on Wireless Sensor Networks

Jiachen Yang, Jianxiong Zhou, Zhihan Lv, Wei Wei, Houbing Song

TL;DR

This paper presents a novel WiFi-based wireless sensor network (WSN) for real-time monitoring of industrial carbon monoxide (CO) leaks. The system utilizes a low-frequency modulation method for accurate CO detection and a triangulation algorithm for precise node localization, offering a robust solution for industrial safety.

What Problem Does This Paper Address?

Carbon monoxide (CO) is a highly toxic and flammable gas that poses significant risks in industrial settings, particularly in areas where it's stored or produced. Traditional monitoring methods can be cumbersome or lack the real-time, distributed coverage needed to quickly detect and pinpoint leaks. The paper addresses the need for a reliable, accurate, and spatially aware system that can continuously monitor CO levels in industrial environments, enabling rapid response to potential hazards. Existing wireless sensor network technologies like Zigbee, while accurate, are often too expensive, and Bluetooth has compatibility issues. WiFi offers a good balance of high data rates, long transmission distances, and widespread availability, making it a promising candidate for industrial WSNs.

Methods

The proposed system comprises sensor nodes, WiFi modules, and routers.

  • CO Detection: The sensor nodes employ a pyroelectric sensor coupled with a non-dispersive infrared (NDIR) detection principle. To enhance signal stability and reduce interference, a low-frequency electrical modulation technique is used. This method modulates the infrared light source at specific parameters (T = 180 ms, D = 50%) to improve the signal-to-noise ratio. The CO concentration is then measured based on the Lambert-Beer Law, relating light absorption to gas concentration. Digital filtering is applied to the modulated waveform to further remove noise.
  • Wireless Communication & Localization: WiFi technology is used for wireless communication between sensor nodes and routers. The system leverages a triangulation algorithm for node localization. Each sensor node has a unique Service Set Identifier (SSID) and MAC address. Routers receive signal strength indicators (RSSI) from each node. By knowing the coordinates of at least three routers, the system can calculate the precise location of each sensor node using trilateration, forming a plane Cartesian coordinate system for the industrial plant.
  • Network Management: To conserve power, the WiFi modules operate in a cyclical sleep-wake-execute mode. Nodes sleep for 5 minutes, after which a router initiates a wake-up directive. Nodes respond, their positions are updated, and data is acquired for a minute before returning to sleep.

Datasets

Not discussed in the paper. The experiments were conducted in a controlled laboratory environment and a simulated industrial plant setting.

Key Insights and Ideas

  • Low-Frequency Modulation for Stability: The paper highlights that even with NDIR technology, weak signals are susceptible to interference. The low-frequency modulation technique is crucial for improving the stability and accuracy of the CO concentration measurements, making the system more reliable in noisy industrial environments.
  • WiFi as a Viable Industrial WSN Solution: The authors make a strong case for WiFi's suitability in industrial settings, balancing cost, performance (high data rates, long range), and ubiquity against alternatives like Zigbee and Bluetooth.
  • Triangulation for Precise Localization: Integrating a triangulation algorithm with WiFi's RSSI measurements provides accurate spatial awareness of CO leaks. This is critical for industrial safety, allowing for quick identification of the source and extent of a leak.
  • Energy-Efficient Network Operation: The sleep-wake-execute cycle for WiFi modules is a smart approach to mitigate the high power consumption of WiFi, enabling longer operational periods for the sensor nodes.

Key Results

  • Accuracy: The system demonstrated a minimum detectable concentration of 15 ppm with a relative error of 4.2%, meeting industrial requirements. At higher concentrations (up to 300 ppm), the relative error was significantly lower, down to 1.01%.
  • Stability: A 10-day continuous test showed normalized CO concentration values within -0.02 to 0.01, indicating excellent long-term stability and a better performance of the device.
  • Localization: The triangulation method successfully located sensor nodes, and the system could display their positions in real-time on a PC or smartphone.
  • Leakage Point Prediction: Using Gaussian Process regression, the system could infer CO concentrations at points without sensors and visualize the spatial distribution of CO, effectively identifying potential leakage points.

Limitations and Future Work

  • Limitations: The paper acknowledges that the WiFi module's power consumption necessitates a sleep-wake cycle, meaning continuous monitoring at every second is not achieved. The localization accuracy is dependent on the accuracy of RSSI measurements, which can be affected by environmental factors.
  • Future Work: The authors suggest that the system's effectiveness in real-world industrial environments needs further validation. Potential future work could involve optimizing the energy efficiency further, exploring more advanced localization algorithms, and integrating the system with industrial control systems for automated responses.

Summary updated

Abstract

Carbon monoxide (CO) burns or explodes at over-standard concentration. Hence, in this paper, a Wifi-based, real-time monitoring of a CO system is proposed for application in the construction industry, in which a sensor measuring node is designed by low-frequency modulation method to acquire CO concentration reliably, and a digital filtering method is adopted for noise filtering. According to the triangulation, the Wifi network is constructed to transmit information and determine the position of nodes. The measured data are displayed on a computer or smart phone by a graphical interface. The experiment shows that the monitoring system obtains excellent accuracy and stability in long-term continuous monitoring.
BibTeX
@article{yang2015real,
  author = {Jiachen Yang and Jianxiong Zhou and Zhihan Lv and Wei Wei and Houbing Song},
  title = {{A Real-Time Monitoring System of Industry Carbon Monoxide Based on Wireless Sensor Networks}},
  journal = {Sensors},
  year = {2015},
  doi = {10.3390/s151129535},
}
Figure