A large temperature-controlled static and dynamic mechanical testing apparatus on marine soil-structure interfaces for marine engineering

Bo Yang, Kai Xu, Tang Xiao, Peng Cui, Xianhui FengFrontiers in Marine Science 2025 · DOI

Abstract

Marine soil–structure interfaces are commonly encountered in marine engineering, where they are inevitably subjected to temperature variations and complex stress conditions, including static, dynamic, and creep loads. However, limited studies have addressed the temperature-dependent mechanical behavior of marine soil–structure interfaces under various loading scenarios. This study introduces a self-developed multifunctional large-scale shear apparatus that enables temperature-controlled testing of marine soil interfaces with various structural materials, including concrete, polymer grids, and polymer layers. The apparatus supports static, dynamic, and creep shear testing under precisely controlled thermal conditions. A series of shear tests were conducted on marine soil–concrete, marine soil–polymer grid, and marine soil–polymer layer interfaces to verify the device’s performance. The test results demonstrate that the apparatus can accurately and reliably capture the mechanical responses of marine soil–structure interfaces under different temperatures and loading modes. Furthermore, the results highlight the significant influence of temperature on the shear behavior of these interfaces, emphasizing the necessity of developing such equipment. The findings offer essential insights for the design, evaluation, and long-term stability of marine engineering structures, supporting the development of practical ocean solutions.

Introduction

In marine engineering, the interface where soil meets a structure—such as a concrete pile or a polymer-coated pipeline—is often the most vulnerable point. Failure at this interface can compromise the integrity of the entire structure. While standard testing methods exist, they frequently overlook the critical variable of temperature. Real-world marine environments are thermally dynamic; subsea oil and gas pipelines can reach 80°C, while coastal structures in hot climates may experience temperatures of 70–80°C due to solar radiation. Conversely, arctic regions present sub-freezing conditions. These thermal shifts alter the liquidity of pore water and the soil's microstructure, significantly impacting mechanical strength. Current testing rigs often lack the capability to combine precise temperature control with the complex loading (static, cyclic, and long-term creep) necessary to simulate a structure's full lifecycle.

Methodology and Apparatus Design

To address this gap, researchers developed a multifunctional large-scale interface shear apparatus. This device integrates several key technical features to simulate harsh marine environments accurately.

Schematic and photo of the in-house developed temperature-regulated large interface shear device.

The apparatus features:

  • Temperature Control: A heating plate and water bath system maintain temperatures between -5°C and 300°C with a precision of ±0.1°C.
  • Versatile Loading Modes: A servo-controlled system supports monotonic (static) loading to failure, cyclic (dynamic) loading to simulate waves or seismic events, and creep testing for long-term deformation under sustained loads.
  • High-Precision Sensing: A dual-feedback system utilizes sensors with 0.002 mm displacement resolution and 0.1 kN stress precision.

The internal testing device, shown in detail below, allows for the testing of various structural materials against marine soils like coral and silica sand.

Detailed view of the internal testing device components.

Key Insights and Experimental Results

Validation tests involved over 20 combinations of normal stress (25–150 kPa) and temperatures (-5°C to 200°C) using materials such as sustainable cement mortar (from recycled concrete), polymer grids, and polymer layers.

Thermal Impact on Shear Strength

A primary finding is the "weakening effect" of heat. As temperature increases, the peak shear strength of the interface consistently decreases. For example, in marine soil–concrete interface tests at 25 kPa normal stress, the peak shear strength dropped from 23.6 kPa at 40°C to 15.9 kPa at 100°C. This suggests that room-temperature testing may lead to overestimations of safety in high-temperature applications.

Temperature-Sensitive Creep and Dynamic Stability

Long-term deformation, or creep, was found to accelerate significantly at higher temperatures. At 90% of peak shear strength, interface displacement at 200°C was 4.19% higher than at 60°C after 3,000 minutes. Furthermore, the apparatus demonstrated excellent stability during dynamic tests, maintaining precise temperature control (within 0.2°C fluctuation) over 20 cycles of dynamic loading, proving its efficacy in simulating wave-induced stresses.

Conclusion and Future Directions

The developed apparatus provides a robust platform for characterizing both hard (concrete-soil) and flexible (polymer-soil) interfaces under extreme thermal conditions. While the results are promising, future work will focus on expanding the validation to a broader range of soil compositions and bridging the gap between laboratory results and in-situ seabed conditions. Technical challenges remain, such as maintaining consistent soil moisture during long-term high-temperature tests. Future iterations may also incorporate advanced sensing, such as real-time micromechanical visualization, to further understand soil particle behavior at the interface during shearing.

Summary updated

Abstract

Marine soil–structure interfaces are commonly encountered in marine engineering, where they are inevitably subjected to temperature variations and complex stress conditions, including static, dynamic, and creep loads. However, limited studies have addressed the temperature-dependent mechanical behavior of marine soil–structure interfaces under various loading scenarios. This study introduces a self-developed multifunctional large-scale shear apparatus that enables temperature-controlled testing of marine soil interfaces with various structural materials, including concrete, polymer grids, and polymer layers. The apparatus supports static, dynamic, and creep shear testing under precisely controlled thermal conditions. A series of shear tests were conducted on marine soil–concrete, marine soil–polymer grid, and marine soil–polymer layer interfaces to verify the device’s performance. The test results demonstrate that the apparatus can accurately and reliably capture the mechanical responses of marine soil–structure interfaces under different temperatures and loading modes. Furthermore, the results highlight the significant influence of temperature on the shear behavior of these interfaces, emphasizing the necessity of developing such equipment. The findings offer essential insights for the design, evaluation, and long-term stability of marine engineering structures, supporting the development of practical ocean solutions.
BibTeX
@inproceedings{yang2025large,
  author = {Bo Yang and Kai Xu and Tang Xiao and Peng Cui and Xianhui Feng},
  title = {{A large temperature-controlled static and dynamic mechanical testing apparatus on marine soil-structure interfaces for marine engineering}},
  booktitle = {Frontiers in Marine Science},
  year = {2025},
  doi = {10.3389/fmars.2025.1671265},
}
Figure