TL;DR
This paper introduces a compact, low-profile soft robotic wrist brace that utilizes novel origami-inspired soft actuators. By integrating these actuators onto a commercially available brace, the device offers a customizable and comfortable solution for wrist rehabilitation, achieving a significant range of motion with a lightweight design.
What Problem Does This Paper Address?
Wrist disabilities, often resulting from strokes or injuries, severely impair a person's ability to perform daily activities. While robotic rehabilitation devices offer promising solutions, existing systems often face challenges with bulkiness, discomfort, and high costs, hindering widespread adoption, especially for at-home use. The need for lightweight, flexible, and affordable wearable devices that can provide effective rehabilitation without compromising comfort is a significant unmet need.
Methods
The core innovation lies in the development of Soft Origami Actuators (SOAs). These actuators leverage a modified Yoshimura origami pattern directly integrated into an air cavity. This design allows for linear elongation and contraction when pressurized or depressurized, respectively. To achieve the desired wrist motions (flexion/extension and radial/ulnar deviation), these SOAs are arranged in pairs (2-SOA units) and attached to a fabric wrist brace. The fabric acts as a constraint, reconfiguring the linear motion of the SOAs into bending, thus generating the necessary wrist joint movements. This "soft-on-soft" approach, where soft actuators are constrained by flexible fabric, is a key novelty. The SOAs are mass-produced using a cost-effective blow molding process with ethylene-vinyl acetate (EVA) copolymer. The brace itself is constructed from a commercially available wrist brace, rigid fabric anchors, and a spandex layer for connection. A cascaded control strategy is employed, with a high-level controller managing motion and a low-level controller regulating individual SOAs based on pressure feedback.
Datasets
Not discussed in the paper. The paper focuses on the design, fabrication, and experimental validation of the proposed soft robotic wrist brace.
Key Insights and Ideas
- Origami for Actuation: The paper demonstrates how origami patterns can be directly integrated into pneumatic actuators to create efficient, linear-motion devices. This moves beyond using origami as a passive structural element.
- Soft-on-Soft Constraint: Using the brace's fabric to constrain the linear motion of the SOAs into bending is a clever way to achieve complex joint movements without complex mechanical linkages. This also allows for customization based on user anatomy.
- Modular Design for Customization: The modularity of the SOA units (2-SOA units) allows for easy customization of the brace for individual users and potentially for other wearable robotic applications.
- Mass Production Potential: The use of blow molding for SOA fabrication highlights a pathway to cost-effective, large-scale production of soft actuators, a crucial step for commercial viability.
- Synergistic Actuation: Actuating pairs of SOAs in a coordinated manner (elongation and contraction) significantly enhances the output force compared to individual actuator modes.
Key Results
- Compactness and Lightweight: The proposed SR wrist brace has a compact form factor (160 mm x 110 mm x 85 mm) and weighs approximately 241 g, making it significantly smaller and lighter than many existing soft robotic wrist devices.
- Range of Motion: The brace achieved functional ranges of motion: extension 30°, flexion 31°, radial deviation 33°, and ulnar deviation 22°, which meets the requirements for standardized wrist movements.
- Output Force: The brace generated up to 6 N of force in radial/ulnar deviation, translating to approximately 0.76 Nm of torque, which is about 58% of the average maximal torque of a healthy human wrist.
- Repeatability: Blow molding demonstrated good repeatability for the SOAs, with force-pressure curves showing high conformity across multiple units.
- Performance Under Load: The brace maintained reasonable performance under loads up to 200 g, showing its potential for assistive applications.
- Control Performance: The control system demonstrated good tracking of planned trajectories, especially in the extension/flexion direction, with a bandwidth suitable for applications like mirror therapy.
Limitations and Future Work
- Fabrication Disparities: While blow molding offers mass production advantages, slight variations in origami facet thickness can lead to disparities in actuator performance, particularly at larger deformations.
- Torque Output: The current torque output is approximately 58% of a healthy human wrist's maximum torque. Future work could improve this by increasing SOA facet thickness to allow higher inflation pressures.
- Ulnar/Radial Deviation Stability: The paper notes less stable behavior in ulnar/radial deviation control, potentially due to fabrication inconsistencies.
- Future Work: The authors suggest several avenues for future research:
- Developing a compact wearable system that integrates control systems.
- Further improving output force and range of motion for broader applications like human joint augmentation and motion capture.
- Conducting user case studies to validate effectiveness in specific rehabilitation therapies.
- Optimizing the brace design to further reduce volume and weight for a non-obstructive wearing experience.
- Leveraging the modular actuator approach to construct wearable devices for other human joints.
Summary updated