A Compact Hybrid Battery Thermal Management System for Enhanced Cooling

Zhipeng Lyu, Jinrong Su, Zhe Li, Xiang Li, Hanghang Yan, Lei ChenarXiv 2024 · DOI · arXiv

The Thermal Challenge in Electric Vehicles

As electric vehicles (EVs) evolve, the demand for higher discharge rates and ultra-fast charging has intensified. These conditions cause lithium-ion batteries to generate substantial heat, which, if not managed, leads to thermal runaway or significantly reduced lifespan. Traditional liquid cooling systems are effective but often bulky and energy-intensive. Conversely, passive cooling using Phase Change Materials (PCM) excels at absorbing heat spikes but suffers from a "saturation point"—once the PCM melts, its cooling capacity drops sharply.

Existing hybrid systems that combine both methods often struggle with weight and volume constraints, which are critical factors for vehicle range. Researchers have now proposed a compact hybrid battery thermal management system (HBTMS) that addresses these trade-offs through architectural innovation and advanced fluid dynamics.

A Multi-Pronged Cooling Strategy

The proposed system utilizes a three-pronged approach: Nanofluid Cooling (NC), Phase Change Materials (PCM), and Enhanced Cooling (EC) via pulsed flow.

Instead of external cooling plates, the researchers designed a compact module where U-shaped microchannels are embedded directly between battery rows. The spaces between these channels are filled with a composite of paraffin wax (PCM) and aluminum foam, which compensates for the PCM's naturally low thermal conductivity.

Exploded view and assembly process of the proposed compact battery module and its integration into a vehicle power battery.

To further boost performance, standard water/glycol coolants were replaced with Alumina ($Al_2O_3$) nanofluids. These fluids offer significantly higher thermal conductivity than traditional base fluids, allowing for more efficient heat extraction from the battery cells.

Internal Architecture and Pulsed Flow

The internal layout is optimized to balance active convective cooling with passive latent heat storage. Analysis indicated that a channel height of 7mm provides the ideal "sweet spot," maximizing cooling without displacing too much PCM.

Front and section views of the battery module showing the spatial arrangement of batteries, PCM, and coolant channels.

A key innovation in this system is the "Enhanced Cooling" strategy using a pulsed flow function. Rather than a steady stream, the coolant is delivered in a "step-response coupled Gaussian pulse." This technique is designed to disrupt the thermal boundary layer—a stagnant layer of fluid near the channel walls that typically resists heat transfer. By oscillating the flow, the system "scrubs" heat away more effectively, improving efficiency without requiring a significantly larger pump.

Performance and Efficiency

The HBTMS was evaluated using a thermal-fluid dynamics model in COMSOL Multiphysics, validated against experimental data from ternary lithium-ion batteries. The results demonstrate significant improvements over conventional designs:

  • Temperature Control: The hybrid solution reduced the maximum battery temperature to 38.87°C, a 3.44°C improvement over standard liquid cooling.
  • Energy Efficiency: This performance gain was achieved with only a 5% increase in pumping power consumption, highlighting the effectiveness of the pulsed flow method.
  • Battery Longevity: By maintaining more stable and lower operating temperatures, the system is estimated to extend battery cycle life by 6% to 15%.

Conclusion

This compact hybrid system successfully navigates the trade-off between thermal performance and system volume. By integrating nanofluids and pulsed flow into a PCM-embedded architecture, the researchers have created a solution that is both highly efficient and suitable for the space-constrained environment of modern EVs. Future work will focus on optimizing pulse waveforms and conducting full-scale physical experiments to bring this technology closer to commercial implementation.

Summary updated

BibTeX
@misc{lyu2024compact,
  author = {Zhipeng Lyu and Jinrong Su and Zhe Li and Xiang Li and Hanghang Yan and Lei Chen},
  title = {{A Compact Hybrid Battery Thermal Management System for Enhanced Cooling}},
  year = {2024},
  eprint = {2412.00999},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2412.00999},
}
Figure