323 THE BEHAVIOR OF MAGNESIUM ALLOY DEFORMING UNDER HIGH VELOCITY

Xin Lü, Yang LuyiThe Proceedings of the JSME Materials and Processing Conference (M&P) 2002 · DOI

Abstract

In this paper, the behavior of Magnesium alloy under high velocity is investigated. The relation of dynamic stress and strain is measured by the dynamic uniaxial tensile impacting test and analyses. It is shown that under high velocity, the $\sigma_b$ of Magnesium alloy is increased with velocity increasing, and the ductility is also increased. When velocity goes up to a critical value, the $\sigma_b$ continues to increase, but the ductility decreases rapidly. Electromagnetic forming experiments of Magnesium alloy sheet demonstrate that wood can be used as a die material, offering excellent anti-wrinkle properties and minimal backspring.

Introduction

Magnesium alloys are highly valued in the electronics and automotive industries for their low density, recyclability, and electromagnetic shielding properties. However, their hexagonal close-packed (HCP) crystal structure results in poor formability and brittleness at room temperature under standard processing conditions. This study explores high-velocity deformation as a means to enhance the mechanical properties and manufacturability of AZ31 magnesium alloy.

Experimental Methodology

The researchers utilized two distinct high-velocity approaches:

  1. Dynamic Uniaxial Tensile Impact Test: To characterize material behavior at high strain rates, a "whirl tray" apparatus was employed. This system uses a rotating tray to impact a mass, generating a high-speed stress wave that propagates through the sample. Strain rates of 200 $s^{-1}$, 1000 $s^{-1}$, and 2200 $s^{-1}$ were achieved.
Schematic of the dynamic uniaxial tensile impact test system.
  1. Electromagnetic Forming (EMF): EMF uses pulsed magnetic fields to accelerate metal sheets at high velocities into a die. This process leverages inertial forces, reducing the mechanical pressure on the tooling.
  2. Innovative Tooling: A unique aspect of this research was the use of wooden dies for the EMF process. Given the reduced active force on the die during high-speed forming, the authors hypothesized that wood could serve as a cost-effective alternative to traditional steel dies.

Dynamic Stress-Strain Analysis

The experimental results reveal a significant "velocity effect" on the mechanical properties of the AZ31 alloy. Unlike many metals that become more brittle under impact, magnesium alloy exhibits simultaneous increases in both strength and ductility within the tested range.

Comparative stress-strain curves for AZ31 magnesium alloy at strain rates of 200, 1000, and 2200 s⁻¹.

As shown in the comparative stress-strain data, the ultimate tensile strength ($\sigma_b$) rose from approximately 300 MPa at a strain rate of 200 $s^{-1}$ to 323 MPa at 2200 $s^{-1}$. Crucially, the strain at failure also increased, indicating improved ductility. However, the authors caution that a "critical velocity" exists beyond which ductility is expected to drop sharply, though the $\sigma_b$ may continue to rise.

Electromagnetic Forming Results

The EMF experiments, conducted with a 10KJ energy system, successfully produced AZ31 parts using wooden dies. The high-velocity nature of the process provided several manufacturing advantages:

  • Reduced Backspring: The inertial force ensures the material conforms closely to the die, nearly eliminating the elastic recovery (backspring) typical of magnesium.
  • Anti-Wrinkle Properties: The rapid deformation suppressed common surface defects like wrinkling.
  • Tooling Economy: The success of wooden dies suggests a path toward significantly lower prototyping and small-batch production costs.

Conclusion

High-velocity deformation offers a promising solution to the inherent formability challenges of magnesium alloys. By increasing both strength and ductility, processes like electromagnetic forming can unlock the full potential of these lightweight materials. The viability of wooden dies further enhances the economic appeal of this technology for industrial applications.

Summary updated

Abstract

In this paper, the behavior of Magnesium alloy under high velocity is investigated. The relation of dynamic stress and strain is measured by the dynamic uniaxial tensile impacting test and analyses. It is shown that under high velocity, the 6 _b of Magnesium alloy is increased with velocity increasing, the ductile is also increased too. When velocity goes up to the critical value, the 6_b is still increased, but the ductile is decreased quickly. The electromagnetic forming experiments of Magnesium alloy sheet are made, it shows that the wood can be one of the selections of the die material in electromagnetic forming technology and the Magnesium alloy has better antiwrinkle and little backspring.
BibTeX
@inproceedings{lu2002behavior,
  author = {Xin Lü and Yang Luyi},
  title = {{323 THE BEHAVIOR OF MAGNESIUM ALLOY DEFORMING UNDER HIGH VELOCITY}},
  booktitle = {The Proceedings of the JSME Materials and Processing Conference (M\&P)},
  year = {2002},
  doi = {10.1299/jsmeintmp.10.1.592},
}
Figure