Numerical Simulation and Experimental Validation of Electromagnetic-Impacted Micro-forming Processes of Aluminum Alloy Thin Sheet

Wei Liu, Tao Cheng, Zhenghua Meng, Jiaqi Li, Shangyu HuangLecture Notes in Mechanical Engineering 2024 · DOI · OpenAlex

Abstract

Electromagnetic forming (EMF) is a high-speed technology used to improve the formability of aluminum alloy sheets. However, inherent non-uniform electromagnetic forces often limit its application in micro-forming. This study investigates electromagnetic-impacted micro-forming (EMIMF) processes using flexible mediums—rubber, water, and gas—to distribute force more evenly. Numerical simulations of electromagnetic and mechanical coupled fields, validated by experimental results, demonstrate that electromagnetic-impacted micro-hydroforming (EMIMHF) provides the highest forming accuracy and thickness uniformity for AA5052-O aluminum alloy thin sheets.

The Challenge of Micro-scale Precision

As the demand for micro-scale components in fuel cells and micro-electromechanical systems (MEMS) grows, traditional manufacturing methods face significant hurdles. Electromagnetic forming is favored for its high-speed capabilities, but at the micro-scale, the discrete nature of electromagnetic coils creates "peaks" and "valleys" in the applied force. These irregularities lead to poor dimensional accuracy and uneven thinning in thin metal sheets.

Methodology: Smoothing the Force

To address force non-uniformity, researchers proposed using a flexible medium as a "spatial filter." In this setup, the electromagnetic force drives a piston into a medium (rubber, liquid, or gas), which then transmits a smoothed pressure to the metal sheet.

Schematic of the EMIMF processes for (a) rubber and (b) hydro/pneumatic mediums, including mesh details and die geometry.

The study compared three processes:

  1. Electromagnetic-Impacted Rubber Micro-forming (EMIRMF)
  2. Electromagnetic-Impacted Micro-hydroforming (EMIMHF)
  3. Electromagnetic-Impacted Pneumatic Micro-forming (EMIPMF)

Simulations were performed using LS-DYNA, employing the Finite Element Method (FEM) for solids and the Boundary Element Method (BEM) for electromagnetic fields. The Arbitrary Lagrangian-Eulerian (ALE) algorithm was used to model fluid mediums to prevent mesh distortion.

Key Results: The Superiority of Hydroforming

The investigation revealed that the choice of medium significantly impacts the quality of the micro-channels. Liquid (water) emerged as the most effective medium due to its near-incompressibility and ability to flow into complex die features more readily than solid rubber.

Forming depth and thickness distribution for the EMIMHF process across different discharge voltages in the longitudinal (LD) and transverse (TD) directions.

Key findings include:

  • Forming Accuracy: EMIMHF achieved a filling rate of approximately 86.7%, outperforming both rubber and gas mediums.
  • Thickness Uniformity: The maximum thinning rate for hydroforming was the lowest at 25.4%. In contrast, rubber and pneumatic processes showed thinning rates of 28.6% and 26.2%, respectively.
  • Energy Efficiency: Hydroforming required lower discharge voltages to achieve high accuracy compared to the other methods, making it more energy-efficient.

Conclusion

By utilizing flexible mediums, specifically water, the electromagnetic-impacted micro-forming process successfully mitigates the issues of non-uniform force distribution. This approach significantly enhances the precision and structural integrity of micro-formed aluminum components. Future research will explore the application of this technology to more complex geometries and optimize the mechanical interfaces to further reduce energy loss.

Summary updated

Abstract

Abstract Electromagnetic forming is a kind of high-speed forming technology for improving the formability of aluminum alloy sheets; however, the inherent non-uniform electromagnetic forces always restrict its application into the micro-forming field. Electromagnetic-impacted micro-forming processes were adopted by using flexible mediums for force transmission. The processes of electromagnetic-impacted rubber micro-forming, electromagnetic-impacted micro-hydroforming, and electromagnetic-impacted pneumatic micro-forming were compared to inspect the influences of flexible mediums. The effects of discharge voltages on the electromagnetic-impacted micro-forming processes of an AA5052-O aluminum alloy thin sheet were investigated by the numerical simulation of electromagnetic and mechanical coupled fields. The numerical simulations were validated via comparisons with the experimental results; these showed that the forming accuracy and thickness uniformity of micro-channels were the greatest by the electromagnetic-impacted micro-hydroforming process.
BibTeX
@inproceedings{liu2024numerical,
  author = {Wei Liu and Tao Cheng and Zhenghua Meng and Jiaqi Li and Shangyu Huang},
  title = {{Numerical Simulation and Experimental Validation of Electromagnetic-Impacted Micro-forming Processes of Aluminum Alloy Thin Sheet}},
  booktitle = {Lecture Notes in Mechanical Engineering},
  year = {2024},
  doi = {10.1007/978-3-031-58006-2\_27},
}
Figure