Potentials for Energy Savings and Carbon Dioxide Emissions Reduction in Cement Industry

Shoaib Sarfraz, Ziyad Sherif, Michał Drewniok, Natanael Bolson, Jonathan M. Cullen, Phil Purnell, Mark Jolly, Konstantinos SalonitisLecture Notes in Mechanical Engineering 2025 · DOI · OpenAlex

Abstract

Cement production accounts for 7% of global carbon dioxide emissions, 3 to 4% of greenhouse gas emissions, and 7% of global industrial energy use. Cement demand is continuously increasing due to the rising worldwide population and urbanisation trends, as well as infrastructure development needs. By 2050, global cement production is expected to increase by 12 to 23% from its current level. Following the net-zero carbon 2050 agenda, both energy and emissions must be significantly reduced. Different production routes exist to produce cement that differs in energy intensity as well as carbon intensity. Similarly, a range of values exists related to energy and emissions for the major cement production stages i.e., raw meal preparation, clinkerisation and cement grinding. The same is the case with cement types produced. This study presents a literature review-based investigation and comparison of cement production practices in terms of energy consumption and CO 2 emissions. This will provide perspectives to the cement industry by identifying approaches that are the least energy and emissions intensive.

Introduction

Cement is the literal foundation of modern infrastructure, but its environmental price tag is massive. It accounts for 7% of global industrial energy use and 3% to 4% of all greenhouse gas emissions. With global demand expected to rise by up to 23% by 2050 due to urbanization, the industry faces a paradox: how to build more while emitting significantly less. This study identifies specific "hotspots" in the production chain, evaluating where energy is wasted and where emissions are concentrated—specifically pointing to the clinkerization process—and evaluates which existing technologies can bridge the gap to the 2050 Net-Zero agenda.

Methodology

This study is a literature review-based investigation that synthesizes data from scientific journals and technical reports, such as those from the International Energy Agency (IEA). The research focused on:

  • Benchmarking Production Routes: Comparing the energy intensity of "wet" vs. "dry" manufacturing processes.
  • Stage-by-Stage Analysis: Evaluating the three main stages of production: raw meal preparation, clinkerization (the chemical heart of cement), and finish grinding.
  • Technology Assessment: Identifying "Best Available Technologies" (BAT) and quantifying their potential for energy and emission reductions.

Data was aggregated from global industrial reports and regional case studies, particularly from India and China, to illustrate the impact of material substitution over time.

Key Insights and Technological Pathways

The Clinker Bottleneck

Clinker production is the primary driver of environmental impact, accounting for 85% of total emissions and 99% of thermal energy consumption. This is due to the extreme heat (1450°C) required and the chemical $CO_2$ released during limestone decomposition (calcination).

Process Efficiency and Grinding

Transitioning from a "wet" process to a "dry" process can improve energy efficiency by 26% to 58%. While clinkerization dominates thermal energy, cement finishing (grinding) is the primary electrical consumer, accounting for 34% of a plant's electricity. Replacing traditional ball mills with Vertical Roller Mills (VRMs) in raw material grinding can reduce energy use by 25% and associated $CO_2$ by 57%.

The Role of Supplementary Cementitious Materials (SCMs)

Supplementary Cementitious Materials (SCMs) like fly ash, slag, and Limestone Calcined Clay Cement (LC3) are the most promising levers for deep decarbonization. LC3 alone can offer a 70% reduction in $CO_2$ emissions compared to traditional Ordinary Portland Cement (OPC).

Results: The Impact of Material Substitution

The study highlights that substituting clinker with SCMs can reduce $CO_2$ intensity by up to 75%. In India, the world's second-largest producer, total direct $CO_2$ emissions have been mitigated by increasing the share of blended cements like Portland Pozzolana Cement (PPC) and Portland Slag Cement (PSC), which now constitute 73% of the market.

Comparison of current CO2 emissions with hypothetical scenarios using only PPC or PSC blended cements.

As shown in Figure 2, the adoption of blended cements (PPC and PSC) presents a significant opportunity to decouple production growth from emission increases. Even as total $CO_2$ output rose historically, the potential savings from full adoption of these blended types are substantial.

Limitations and Future Outlook

Despite the potential of these technologies, several hurdles remain:

  • Data Transparency: Proprietary data on specific efficiency gains makes it difficult to establish universal "real-world" performance metrics.
  • Material Availability: The mass production of blended cements is constrained by the local availability of materials like fly ash or slag.
  • Technological Scope: This study focuses on commercialized technologies. Reaching Net-Zero will likely require "frontier" solutions like Carbon Capture and Storage (CCS) or radical alternative fuels.

Future work should focus on industry-wide benchmarking to establish a standardized "best practice" framework across different geographic regions to accelerate the global transition.

Summary updated

Abstract

Abstract Cement production accounts for 7% of global carbon dioxide emissions, 3 to 4% of greenhouse gas emissions, and 7% of global industrial energy use. Cement demand is continuously increasing due to the rising worldwide population and urbanisation trends, as well as infrastructure development needs. By 2050, global cement production is expected to increase by 12 to 23% from its current level. Following the net-zero carbon 2050 agenda, both energy and emissions must be significantly reduced. Different production routes exist to produce cement that differs in energy intensity as well as carbon intensity. Similarly, a range of values exists related to energy and emissions for the major cement production stages i.e., raw meal preparation, clinkerisation and cement grinding. The same is the case with cement types produced. This study presents a literature review-based investigation and comparison of cement production practices in terms of energy consumption and CO 2 emissions. This will provide perspectives to the cement industry by identifying approaches that are the least energy and emissions intensive.
BibTeX
@inproceedings{sarfraz2025potentials,
  author = {Shoaib Sarfraz and Ziyad Sherif and Michał Drewniok and Natanael Bolson and Jonathan M. Cullen and Phil Purnell and Mark Jolly and Konstantinos Salonitis and Jonathan Cullen},
  title = {{Potentials for Energy Savings and Carbon Dioxide Emissions Reduction in Cement Industry}},
  booktitle = {Lecture Notes in Mechanical Engineering},
  year = {2025},
  doi = {10.1007/978-3-031-77429-4\_85},
}
Figure