Abstract
The pole array configuration in surface-mounted permanent magnet (SPM) machines directly influences air-gap field distribution, impacting both average torque and torque ripple. This study utilizes finite element analysis (FEA) to compare radial-magnetized, tangential-magnetized, and Halbach arrays. By analyzing the effects of the pole arc coefficient ($a_p$) and PM thickness coefficient ($a_h$) via fast Fourier transform (FFT), the research identifies critical design trade-offs. Results indicate that while pole arc length significantly affects harmonic components, magnet thickness primarily influences the fundamental flux density. Notably, radial arrays can outperform Halbach arrays at low thicknesses, while tangential arrays emerge as superior when magnet thickness exceeds 0.9 times the pole pitch.
Introduction
In the design of surface-mounted permanent magnet (SPM) machines—essential components in robotics and electric power steering—engineers face a persistent trade-off. The "fundamental wave" of magnetic flux in the air gap determines the average torque (the machine's strength), while "harmonics" (distortions in that wave) cause torque ripple, leading to unwanted vibration and noise. While various magnet arrangements exist, direct head-to-head comparisons across varying physical dimensions have been limited. This paper provides a comprehensive guide for selecting the optimal magnet array and dimensions to balance power and operational smoothness.
Methodology
The researchers employed Finite Element Analysis (FEA) to simulate the magnetic fields of three distinct pole arrays: radial-magnetized, Halbach array, and tangential-magnetized (spoke-type). To ensure universal applicability, the study utilized nondimensionalized coefficients: the pole embrace coefficient ($a_p$), representing the ratio of the magnet's arc length to the total pole pitch, and the pole thickness coefficient ($a_h$), the ratio of magnet thickness to the pole pitch. Fast Fourier Transform (FFT) was then applied to the resulting flux density waveforms to isolate fundamental torque-producing waves from harmonic ripple-producing waves.
The Impact of Geometric Ratios
A key finding of the study is the distinct roles played by $a_p$ and $a_h$. The pole arc length ($a_p$) acts as a "harmonic knob." By tuning this ratio, designers can effectively cancel out specific harmonics (such as the 3rd, 5th, or 7th) that contribute to vibration.
As shown in Figure 5, varying the pole arc ratio leads to significant fluctuations in harmonic content, allowing for targeted optimization. For radial motors, a ratio between 0.8 and 0.857 is identified as the "sweet spot" for minimizing ripple. Conversely, the magnet thickness ($a_h$) primarily impacts the total torque (fundamental flux) with minimal effect on harmonic distortion.
Figure 3 illustrates that as the magnet volume increases, the fundamental flux density grows, but the harmonic levels remain relatively flat. This suggests that designers can increase magnet volume to boost power without necessarily increasing the motor's acoustic or vibrational signature.
Comparative Performance and Results
The comparative analysis revealed several surprising insights regarding the three array types:
- Thin Magnet Performance: When magnets are thin (small $a_h$), the radial-magnetized array performs better than both Halbach and tangential arrays regarding fundamental flux density.
- The Halbach Advantage: Generally, Halbach arrays provide higher torque density than radial arrays and exhibit perfectly symmetrical harmonic distributions.
- The Tangential Takeover: Perhaps the most significant result is that when magnet thickness exceeds 0.9 times the pole distance, the tangential-magnetized array produces a higher fundamental magnetic density than the Halbach array.
- Saturation Effects: Tangential arrays are heavily influenced by iron saturation between magnets, which prevents the fundamental wave from growing linearly with the pole arc, unlike Halbach or radial arrays.
Conclusion
This study clarifies the design space for SPM machines by quantifying how geometric ratios influence magnetic performance across different array types. While radial arrays are effective for thin-magnet designs, Halbach and tangential arrays offer superior performance as magnet volume increases, with tangential arrays becoming particularly advantageous at high thicknesses.
The current analysis relies on a 2D linear geometric model, which is most accurate for high-pole-count motors where rotor curvature is minimal. Future research should incorporate mechanical constraints, such as magnet retention at high speeds, and thermal effects, as the more complex Halbach and tangential arrangements present unique manufacturing and cooling challenges.
Summary updated