Comment on egusphere-2022-438

Duncan Watson‐ParrisOpenalex Unknown 2022 · DOI · OpenAlex

Abstract

Aerosols have a large impact on climate, air quality, and biogeochemical cycles. Their concentrations are highly variable in space and time, and a key variability is in their vertical distribution, because it influences atmospheric heating profiles, aerosols life-time and, as a result, surface concentrations, and because it has an impact on aerosol-cloud interactions. On the side of model-oriented aerosols research, using a lidar aerosol simulator ensures consistent comparisons between the modeled aerosols and the observed aerosols. In the current study, we present the lidar aerosol simulator implemented within the COSPv2 satellite lidar simulator. We estimate the total attenuated backscattered signal (ATB) and the scattering ratios (SR) that would be observed at 532 nm by the lidar CALIOP overflying the atmosphere predicted by the E3SMv1 climate model. The simulator performs the computations at the same vertical resolution as the CALIOP lidar, making use of aerosol optics from the E3SMv1 model as inputs, and assuming that aerosols are uniformly distributed horizontally within each model grid-box. It applies a cloud masking and an aerosol detection threshold, to get the ATB and SR profiles that would be observed above clouds by CALIOP with its actual aerosol detection capability. Our comparison shows that the aerosol distribution simulated at a seasonal timescale is generally in good agreement with observations, with however a discrepancy in the Southern Hemisphere, as the observed SR maximum is not reproduced in simulations there. Comparison between cloud-screened and non cloud-screened computed SRs shows little differences, indicating that the cloud screening by potentially incorrect model clouds does not affect the mean aerosol signal averaged over a season. Consequently, the differences between observed and simulated SR values are not due to sampling errors, and allow to point out some weaknesses in the aerosol representation in models. The use of lidar observations at several wavelengths can give further indication on the nature of the aerosols that need to be improved.

Introduction

Aerosols—tiny particles like dust, smoke, and sea spray—play a critical role in the Earth's climate system by reflecting sunlight and influencing cloud formation. However, their vertical distribution is notoriously difficult to model correctly. While space-borne lidars like CALIOP provide high-resolution vertical profiles, comparing this data to climate model output is often inconsistent due to differences in spatial resolution and instrument-specific effects like cloud masking and signal-to-noise thresholds. To bridge this gap, researchers have developed a new simulator that allows for an "apples-to-apples" comparison between model predictions and satellite observations.

The COSPv2 Aerosol Lidar Simulator

The authors implemented a new aerosol module within the CFMIP Observation Simulator Package (COSPv2). This framework is already a standard in many climate modeling centers for evaluating clouds, making this new tool easily accessible for the broader research community.

Key technical features of the simulator include:

  • Variable Translation: It converts model-predicted aerosol extinction and backscatter into Attenuated Total Backscatter (ATB) and Scattering Ratio (SR) at 532 nm.
  • High Vertical Resolution: Unlike standard cloud simulators, this module operates on 320 levels (60m resolution) to capture thin aerosol layers near the surface.
  • Instrument Realism: It applies a cloud mask and an aerosol detection threshold to mimic the signal-to-noise limitations of the CALIOP lidar.
  • Molecular Accounting: It calculates Rayleigh (molecular) backscatter based on the model’s own temperature and pressure profiles to ensure the simulated background matches the model's physics.

Evaluation and Key Insights

The study demonstrated the simulator's utility by comparing the E3SMv1 climate model against CALIOP Level 1.5 observational data. Several significant findings emerged:

The "Sampling Error" Myth

One of the most important conclusions is that cloud screening does not significantly bias seasonal aerosol means. Researchers often worry that because lidars cannot see through thick clouds, the resulting "clear-sky only" data is biased. This study shows that the differences between models and observations are likely due to flaws in model physics—such as emission or transport parameterizations—rather than sampling errors.

Southern Hemisphere Discrepancies

The E3SMv1 model failed to reproduce a major aerosol maximum observed in the Southern Hemisphere, likely associated with marine sea spray. This highlights a specific area where marine aerosol parameterizations in current models need improvement.

Quantitative Biases and Optical Depth

In the lowest 4 km of the atmosphere, the model underestimated the Scattering Ratio (SR) maxima by a factor of 1 to 1.5. This vertical distribution bias translates to a roughly 50% relative error in aerosol optical depth in certain regions. This proves that even if a model correctly predicts the total column of aerosols, it may still be getting the vertical "stacking" wrong, which has major implications for atmospheric heating profiles.

Conclusion and Future Work

The integration of the aerosol lidar simulator into COSPv2 provides a robust tool for evaluating and improving aerosol representations in global climate models. Future updates aim to include additional wavelengths (1064 nm and 355 nm) to support upcoming missions like EarthCARE/ATLID. Additionally, the authors suggest using the simulator to evaluate specific aerosol types (e.g., distinguishing dust from smoke) to better pinpoint which model components require refinement.

Summary updated

Abstract

<strong class="journal-contentHeaderColor">Abstract.</strong> Aerosols have a large impact on climate, air quality, and biogeochemical cycles. Their concentrations are highly variable in space and time, and a key variability is in their vertical distribution, because it influences atmospheric heating profiles, aerosols life-time and, as a result, surface concentrations, and because it has an impact on aerosol-cloud interactions. On the side of model-oriented aerosols research, using a lidar aerosol simulator ensures consistent comparisons between the modeled aerosols and the observed aerosols. In the current study, we present the lidar aerosol simulator implemented within the COSPv2 satellite lidar simulator. We estimate the total attenuated backscattered signal (ATB) and the scattering ratios (SR) that would be observed at 532 nm by the lidar CALIOP overflying the atmosphere predicted by the E3SMv1 climate model. The simulator performs the computations at the same vertical resolution as the CALIOP lidar, making use of aerosol optics from the E3SMv1 model as inputs, and assuming that aerosols are uniformly distributed horizontally within each model grid-box. It applies a cloud masking and an aerosol detection threshold, to get the ATB and SR profiles that would be observed above clouds by CALIOP with its actual aerosol detection capability. Our comparison shows that the aerosol distribution simulated at a seasonal timescale is generally in good agreement with observations, with however a discrepancy in the Southern Hemisphere, as the observed SR maximum is not reproduced in simulations there. Comparison between cloud-screened and non cloud-screened computed SRs shows little differences, indicating that the cloud screening by potentially incorrect model clouds does not affect the mean aerosol signal averaged over a season. Consequently, the differences between observed and simulated SR values are not due to sampling errors, and allow to point out some weaknesses in the aerosol representation in models. The use of lidar observations at several wavelengths can give further indication on the nature of the aerosols that need to be improved.
BibTeX
@inproceedings{watsonparris2022comment,
  author = {Duncan Watson‐Parris},
  title = {{Comment on egusphere-2022-438}},
  booktitle = {Openalex Unknown},
  year = {2022},
  doi = {10.5194/egusphere-2022-438-rc1},
}
Figure