Wireless Powered Encoding and Broadcasting of Frequency Modulated Detection Signals

Wei Qian, Xin Yu, Chunqi QianIEEE Access 2020 · DOI

TL;DR

This paper introduces a novel wireless modulator that can simultaneously down-convert and frequency-encode RF signals onto a carrier wave, eliminating the need for bulky external components. This compact, low-power device holds promise for improving the detectability and flexibility of implantable and interventional medical devices.

What Problem Does This Paper Address?

Long-term operation of embedded medical transducers, especially those in confined body cavities, requires wireless power and data transmission. While existing wireless transducers are effective for low-frequency signals, encoding higher-frequency RF signals (like those used in MRI) typically involves complex, multi-stage circuits that consume significant power and are large in size. This limits their applicability for miniaturized, implantable devices. The authors aim to solve this by developing a single-stage, compact, and low-power modulator that can directly encode RF signals onto a carrier wave, enabling efficient wireless communication over larger distances.

Methods

The core of the proposed modulator is a "double frequency parametric resonator" coupled with a "single frequency passive resonator." This coupled resonator system is designed to:

  • Parametric Oscillation: Convert wireless pumping power into sustained oscillation currents at specific resonant frequencies.
  • Frequency Modulation: When an input RF signal with a frequency offset is present, it frequency-modulates the oscillation signal. This modulation is achieved by exploiting the nonlinear capacitance of the varactors within the parametric resonator.
  • Simultaneous Down-conversion and Encoding: The parametric oscillator inherently combines the down-conversion of the input RF signal with its frequency encoding onto the carrier wave, all within a single stage.
  • Passive Activation: The modulator is activated by an external pumping field, eliminating the need for an onboard power source.

The design involves careful adjustment of the substrate thickness between the resonators to tune the resonance frequencies, allowing for efficient power conversion and frequency modulation.

Datasets

Not discussed in the paper. The paper focuses on the design, simulation, and experimental characterization of the proposed modulator.

Key Insights and Ideas

  • Single-Stage RF Encoding: The most significant insight is the demonstration of a single-stage circuit that can perform both down-conversion and frequency encoding of RF signals. This bypasses the need for complex digital signal processing or multi-stage analog down-conversion.
  • Parametric Oscillator for FM: Leveraging the nonlinear characteristics of a parametric oscillator to achieve frequency modulation of a carrier signal is a key innovation. This allows for direct encoding of RF inputs.
  • Improved Detectability for Implantable Devices: The ability to encode signals at higher frequencies and transmit them wirelessly over greater distances directly addresses a major limitation for implantable and interventional medical devices, potentially improving image sensitivity and reducing the need for invasive wired connections.
  • Low Power Consumption: The modulator is designed to be wirelessly powered, requiring only a modest pumping power (around 9 dBm) for activation, which is crucial for long-term implantable applications.

Key Results

  • Frequency Modulation Demonstrated: The modulator successfully encoded an input RF signal onto its oscillation signal, creating distinct sidebands separated by the input signal's offset frequency, as shown in the frequency spectrum (Figure 6).
  • Linear Input-Output Relationship: The frequency deviation magnitude was shown to be linearly proportional to the input RF signal power over a significant dynamic range (75 dB), validating the theoretical predictions (Figure 8).
  • Offset-Independent Frequency Response: The demodulated output maintained a consistent magnitude of frequency deviation across a range of input offsets, indicating robust performance (Figure 9).
  • Enhanced MRI Signal Transmission: In MR experiments, the modulator demonstrated significantly improved signal-to-noise ratio (SNR) compared to passive inductive coupling, especially at larger distances. It maintained constant sensitivity for transmission attenuation up to 34 dB, outperforming a regenerative amplifier which could only handle up to 21 dB.
  • Flatter Image Baselines: Images reconstructed using the frequency modulation technique exhibited flatter baselines, indicating better noise immunity compared to regenerative amplification, particularly at higher transmission attenuations.

Limitations and Future Work

  • Image Mirroring: The reconstructed MR images exhibited mirroring in both dimensions due to the cosine-encoding relation of the message signal. The authors suggest that further work could explore pre-emphasis filtering or a chain of parametric oscillators to mitigate this.
  • Noise Immunity: While the modulator shows good noise immunity, the paper notes that for very large transmission attenuations, the baseline of the FM-demodulated image can become uneven, indicating that the modulator's capability to overcome attenuation has limits.
  • Further Optimization: The authors suggest exploring midfield power transfer schemes and improved antenna designs to further reduce the required pumping power. They also mention ongoing work on incorporating pre-emphasis filtering and using multiple parametric oscillators for enhanced performance.

Summary updated

BibTeX
@article{qian2020wireless,
  author = {Wei Qian and Xin Yu and Chunqi Qian},
  title = {{Wireless Powered Encoding and Broadcasting of Frequency Modulated Detection Signals}},
  journal = {IEEE Access},
  year = {2020},
  doi = {10.1109/access.2020.3035938},
}
Figure