Wearable Ball-Impact Piezoelectric Multi-Converters for Low-Frequency Energy Harvesting from Human Motion

Alessandro Nastro, Nicola Pienazza, Marco Baù, Pietro Aceti, Markku Rouvala, Raffaele Ardito, Marco Ferrari, Alberto Corigliano, Vittorio FerrariSensors 2022 · OpenReview

TL;DR

This paper introduces novel wearable piezoelectric energy harvesters that use a free-moving steel ball to convert low-frequency human motion into higher-frequency electrical signals. Prototypes tested on a wrist demonstrated the ability to generate usable energy, paving the way for self-powered wearable electronics.

What Problem Does This Paper Address?

The proliferation of wearable electronic devices (smartwatches, fitness trackers, medical sensors) is hampered by their reliance on batteries, which require frequent recharging or replacement. While energy harvesting offers a solution, existing methods often struggle with the low-frequency, non-periodic nature of human motion. Many piezoelectric harvesters are designed for specific resonant frequencies, making them inefficient for the irregular movements of daily life. This paper tackles the challenge of efficiently capturing and converting the broad spectrum of low-frequency mechanical energy from human motion into electrical energy suitable for powering these devices.

Methods

The core innovation lies in the "ball-impact multi-converter" design. Instead of relying on precise resonant frequencies, these harvesters utilize a small steel ball confined within a compact structure. When the wearer moves their wrist (shakes, tilts), the ball rolls and impacts piezoelectric converters (PCs) configured as cantilevers. This impact-based mechanism inherently up-converts the low-frequency input motion into higher-frequency electrical signals from the PCs.

The researchers developed two configurations:

  • Mono-axial: Uses two PCs, sensitive to motion along a single axis.
  • Bi-axial: Employs four PCs, capable of harvesting energy from motion in two perpendicular axes.

The captured AC electrical signals from the PCs are then rectified using passive diode-based voltage-doubler circuits and stored in a capacitor. Analytical modeling was performed to understand the impact dynamics and predict the system's behavior. Prototypes were fabricated using FR-4 layers and tested by attaching them to a person's wrist.

Datasets

Not discussed in the paper. The experiments were conducted using custom-built prototypes and human motion as the input energy source.

Key Insights and Ideas

  • Frequency Up-Conversion via Impact: The most significant insight is the effective use of a free-moving ball to induce impacts that generate electrical signals at frequencies much higher than the input motion. This bypasses the limitations of resonant harvesters for irregular human movements.
  • Mono- vs. Bi-axial Design: The bi-axial design, with its four PCs, offers greater potential for energy harvesting by capturing motion from multiple directions, making it more robust for diverse human activities.
  • Wearability and Integration: The prototypes were designed to be integrated into wristbands and watchbands, demonstrating a clear path towards practical, wearable energy harvesting solutions.
  • Modeling and Validation: The analytical model provided a good basis for understanding the impact mechanics, and the experimental results validated the model's predictions and the overall concept.

Key Results

  • Mono-axial Harvester: Achieved a stored voltage of 40.2 V across a 220 nF capacitor after 8.5 seconds of wrist rotations, corresponding to 178 µJ of stored energy.
  • Bi-axial Harvester: Demonstrated a peak instantaneous power of 1.58 mW and an average power of 9.65 µW over 0.7 seconds when connected to an optimal resistive load.
  • Frequency Enhancement: The generated AC voltage frequency was observed to be almost three orders of magnitude higher than the excitation frequency (e.g., ~2.7 kHz impact frequency from ~4 Hz wrist rotation).

Limitations and Future Work

  • Durability and Fatigue: The authors acknowledge that piezoceramic elements can be susceptible to long-term durability issues and fatigue from repeated impacts.
  • Impact Location: The current design's performance might be affected by where the ball impacts the cantilevers. Future work could analyze the effect of impacts occurring at different points.
  • Reliability: Ongoing activities are focused on investigating the reliability of the harvesters.
  • Optimization: While promising results were achieved, further optimization of the harvester structure, ball size, and electrical circuit parameters could lead to even higher energy generation. The trade-off between storage capacitance, charging time, and stored energy was highlighted, suggesting further research into optimal capacitor selection for specific applications.

Summary updated

Abstract

Multi-converter piezoelectric harvesters based on mono-axial and bi-axial configurations are proposed. The harvesters exploit two and four piezoelectric converters (PCs) and adopt an impinging spherical steel ball to harvest electrical energy from human motion. When the harvester undergoes a shake, a tilt, or a combination of the two, the ball hits one PC, inducing an impact-based frequency-up conversion. Prototypes of the harvesters have been designed, fabricated, fastened to the wrist of a person by means of a wristband and watchband, and experimentally tested for different motion levels. The PCs of the harvesters have been fed to passive diode-based voltage-doubler rectifiers connected in parallel to a storage capacitor, Cs = 220 nF. By employing the mono-axial harvester, after 8.5 s of consecutive impacts induced by rotations of the wrist, a voltage vcs(t) of 40.2 V across the capacitor was obtained, which corresponded to a stored energy of 178 μJ. By employing the bi-axial harvester, the peak instantaneous power provided by the PCs to an optimal resistive load was 1.58 mW, with an average power of 9.65 μW over 0.7 s. The proposed harvesters are suitable to scavenge electrical energy from low-frequency nonperiodical mechanical movements, such as human motion.
BibTeX
@inproceedings{nastro2022wearable,
  author = {Alessandro Nastro and Nicola Pienazza and Marco Baù and Pietro Aceti and Markku Rouvala and Raffaele Ardito and Marco Ferrari and Alberto Corigliano and Vittorio Ferrari},
  title = {{Wearable Ball-Impact Piezoelectric Multi-Converters for Low-Frequency Energy Harvesting from Human Motion}},
  booktitle = {Sensors},
  year = {2022},
  url = {https://openreview.net/forum?id=wdtHiuNWJ5i},
}
Figure