Versatile Nanoscale Three-Terminal Memristive Switch Enabled by Gating

Mila Lewerenz, Elias Passerini, Bojun Cheng, Markus Fischer, Alexandros Emboras, Mathieu Luisier, Ueli Koch, Juerg LeutholdACS 2024 · DOI

TL;DR

Researchers have developed a novel three-terminal memristive switch with an incredibly small footprint, enabling two distinct operating modes: tuning the set voltage and directly triggering resistance changes with a gate pulse. This highly versatile device demonstrates excellent endurance and reliability, paving the way for advanced applications in neuromorphic computing and the Internet-of-Things.

What Problem Does This Paper Address?

Traditional two-terminal (2T) memristors, while offering compact dimensions and low power consumption, face limitations in advanced computing applications. These include the need for external selectors, the coupling of read and set operations to the same electronic contacts, and device-to-device variations in set voltages that complicate integration into large arrays. The introduction of a third terminal, a gate, offers a potential solution by providing an additional degree of control over the memristor's resistance. While previous research has explored 3T memristors for initiating switching or tuning set voltages, this paper addresses the need for a device that can achieve both functionalities simultaneously and efficiently, particularly at low gate voltages and within a highly compact form factor.

Methods

The core of this work is a novel three-terminal (3T) electrochemical metallization (ECM) memristor fabricated with an ultrasmall footprint of 0.07 µm² and critical dimensions of 70 nm × 10 nm × 6 nm. The device consists of a source (Ag), a drain (Pt), and a side gate (Pt) separated by a switching medium (SiO₂).

The researchers employed two primary characterization methods:

  • DC IV Measurements: This standard technique was used to probe the fundamental memristive behavior of the device. By sweeping the voltage between the source and drain (VSD) while keeping the gate voltage (VGD) either floating or at a constant offset, they analyzed the current-voltage characteristics, including the set voltage (Vset) and ON-resistance.
  • Pulsed Measurements (1 kHz): To assess the device's dynamic response, endurance, and suitability for real-world applications, a 1 kHz pulsed operation was implemented. This involved applying constant bias voltages and square-shaped gate voltage pulses. The source-drain voltage (VSD) was monitored to extract the device resistance (RDUT). This method allowed for the evaluation of resistance switching triggered by gate pulses and endurance testing over millions of cycles.

A key innovation is the demonstration of two distinct operation modes enabled by the gate:

  1. "Set-voltage-tuning" mode: Here, a constant gate voltage offset is applied to influence the DC IV switching characteristics, effectively shifting the set voltage.
  2. "Switching" mode: In this mode, the gate pulse directly modulates the resistance switching, with the source-drain bias voltage held constant.

Datasets

Not discussed in the paper. The experiments involved characterization of the fabricated memristor devices.

Key Insights and Ideas

  • Dual-Mode Operation: The most significant insight is the successful implementation of two distinct operating modes within a single, compact 3T memristor: set-voltage tuning and direct resistance switching via gate pulses. This dual functionality greatly enhances the device's versatility.
  • Low-Voltage Gate Control: The ability to tune the set voltage by a substantial 69.2% with a low gate voltage of just ±1 V is a crucial finding, suggesting efficient control without requiring high power.
  • Gate-Triggered Switching: Demonstrating that a gate pulse can directly induce resistance changes in the device opens up new possibilities for direct control and signal processing.
  • Exceptional Endurance: The device exhibits remarkable endurance, reliably switching over 2.6 million cycles without degradation, a critical factor for practical applications.
  • High Reliability and Reproducibility: The research shows minimal device-to-device variation and consistent performance across multiple devices, which is essential for scalable integration.
  • Open Eye Diagram for PRBS: The device's ability to respond to pseudorandom bit sequences (PRBS) with an open eye diagram and a high success rate (97%) highlights its potential for data storage and communication applications.

Key Results

  • Ultrasmall Footprint: The memristor boasts a footprint of only 0.07 µm² and critical dimensions of 70 nm × 10 nm × 6 nm.
  • Set Voltage Tuning: A gate voltage of ±1 V can shift the set voltage by 69.2% (from 0.325 V to 0.55 V).
  • High-to-Low Resistance Ratio: The "switching" mode achieved a high-to-low resistance ratio of 18.9.
  • Endurance: The device demonstrated reliable switching over 2.6 million voltage pulses.
  • Device-to-Device Variation: Minor variations were observed across four devices tested for 500k cycles, indicating good reproducibility.
  • PRBS Performance: A success rate of approximately 97% was achieved for PRBS inputs, with an open eye diagram indicating robust signal integrity.

Limitations and Future Work

  • RC Time Constant Limitation: The current setup's RC time constant (160 µs) limits the investigation of faster switching speeds. The authors suggest that further investigations using lower resistances and devices that can withstand higher currents are needed to explore higher speeds.
  • Noise Limit: The high resistances in the system lead to a noise limit, which can affect the accuracy of resistance measurements. The authors implemented a noise subtraction method to mitigate this.
  • Future Work: The authors suggest that this device concept is a promising candidate for various applications, including:
  • Neuromorphic Computing: Tuning spike probabilities in artificial neurons and adjusting synaptic weights.
  • Reservoir Computing: Leveraging the nonlinear electrical response for mapping inputs to high-dimensional feature spaces.
  • Internet-of-Things (IoT): The demonstrated time scales and voltages are suitable for IoT applications.
  • Memristive Logic Systems: Developing novel logic circuits.

Summary updated

Abstract

A three-terminal memristor with an ultrasmall footprint of only 0.07 μm<sup>2</sup> and critical dimensions of 70 nm × 10 nm × 6 nm is introduced. The device's feature is the presence of a gate contact, which enables two operation modes: either tuning the set voltage or directly inducing a resistance change. In <i>I</i>-<i>V</i> mode, we demonstrate that by changing the gate voltages between ±1 V one can shift the set voltage by 69%. In pulsing mode, we show that resistance change can be triggered by a gate pulse. Furthermore, we tested the device endurance under a 1 kHz operation. In an experiment with 2.6 million voltage pulses, we found two distinct resistance states. The device response to a pseudorandom bit sequence displays an open eye diagram and a success ratio of 97%. Our results suggest that this device concept is a promising candidate for a variety of applications ranging from Internet-of-Things to neuromorphic computing.
BibTeX
@inproceedings{lewerenz2024versatile,
  author = {Mila Lewerenz and Elias Passerini and Bojun Cheng and Markus Fischer and Alexandros Emboras and Mathieu Luisier and Ueli Koch and Juerg Leuthold},
  title = {{Versatile Nanoscale Three-Terminal Memristive Switch Enabled by Gating}},
  booktitle = {ACS},
  year = {2024},
  doi = {10.1021/acsnano.3c11373},
}
Figure